For Sale/Swap at FTFF East 2017
- Thread starter earthsciteach
- Start date
So far I'm planning to bring the following for swap/sale:
Taranis X9D case, painted metallic green
Taranis X9D case, painted gold
Orange 250 class quadcopter w/ Naze32 clone board, 2204 motors w/ built in 20 amp esc, VTX, camera, etc. - fully setup for FPV - a beginners quad - will sell cheap to good home with lots of spare props
Taranis X9D case, painted metallic green
Taranis X9D case, painted gold
Orange 250 class quadcopter w/ Naze32 clone board, 2204 motors w/ built in 20 amp esc, VTX, camera, etc. - fully setup for FPV - a beginners quad - will sell cheap to good home with lots of spare props
Last edited:
I have nothing specific to sell, but, I will have my full compliment of multirotors. If anyone wants to see any of them and are so inclined to buy/trade, I may be convinced to let them go for a reasonable exchange of $$$ or gear. I'm a build junky, so getting rid of some would feed back into me building and learning more. PM me here or stalk me there and we can set up a time to meet and possibly test fly.
Things I will definitely have with me and could possibly part with:
FlexRC 118mm 3" blade Owls
RCExplorer Baby Tricopters (5" blade)
RMRC Hellbender 204 5"(V1 is currently built, may have a V2 by then too)
STRIX AWK210 5"(currently my best flyer)
I should also have a full compliment of tools and parts should anyone need help debugging their gear. I run spektrum RX/TX, so can't help too much with issues related specifically to other RX/TX protocols.
Camping on site from start too finish...
SEE YOU THERE!
Cheers!
LitterBug
Things I will definitely have with me and could possibly part with:
FlexRC 118mm 3" blade Owls
RCExplorer Baby Tricopters (5" blade)
RMRC Hellbender 204 5"(V1 is currently built, may have a V2 by then too)
STRIX AWK210 5"(currently my best flyer)
I should also have a full compliment of tools and parts should anyone need help debugging their gear. I run spektrum RX/TX, so can't help too much with issues related specifically to other RX/TX protocols.
Camping on site from start too finish...
SEE YOU THERE!
Cheers!
LitterBug
I have a flysky FS-T6 transmitter. It has 6 channels and a 20 model memory. It was a great radio for me when I got into the hobby but I have now moved on to Spektrum radios. I would like to get $25 out of it but I would also be very open to trades.
I also have a small staggerwing. I don't know very much about it as it was a flea market find but I would be happy to try and answer any questions about it. It has a brushed motor and ESC with two micro servos. All of the electronics were tested and work. There is some light damage to it as in scratches in the paint and a few cracks in the foam. I am looking to get $15 out of it but would again be open to trades.
I also have a small staggerwing. I don't know very much about it as it was a flea market find but I would be happy to try and answer any questions about it. It has a brushed motor and ESC with two micro servos. All of the electronics were tested and work. There is some light damage to it as in scratches in the paint and a few cracks in the foam. I am looking to get $15 out of it but would again be open to trades.
I have a couple of these but I'm not sure I'm willing to part with them right now. I've never seemed to keep momentum going on my P-47 Razorback that has a glass fuselage. Great flying bird, but heavy for its size and I've not been able to dial in the flap-elevator mix just right.
My TopFlite AT-6 Texan is spoken for. I also have kits (mostly un-built) for TopFlite 0.60 size Corsair and Mustang. One of which I hope to build with Carl (Wilmracer) over the winter. Then there is the Fokker DVI as well that needs to be finished. Far too many unfinished projects.
My TopFlite AT-6 Texan is spoken for. I also have kits (mostly un-built) for TopFlite 0.60 size Corsair and Mustang. One of which I hope to build with Carl (Wilmracer) over the winter. Then there is the Fokker DVI as well that needs to be finished. Far too many unfinished projects.
I don't have a list on hand, but because I will be flying out and building a lot, I could be persuaded to sell/trade whatever I build (along with whatever internals you like), so that I don't have to figure out how to get it all back home! (short of dismantling everything, which is always the default)
Come find me...I'll be the guy with the jets.
Come find me...I'll be the guy with the jets.
I will be bringing stuff to show...as far as swap goes I don't know....
I have got a Diels Engineering DO 335 (pfeil) arrow, a Golden Age Reproductions P-51 B/C an A Classic Aviation Models (formerly Monogram) Speedee Bilt P-51D kit plus a whole slue of Guillows kits all unbuilt. I'm not going to let any of these go until I copy the plans and duplicate the parts onto fresh balsawood. The mustang and the Guillows planes I'd want to convert to electric, I'd also like to find scale 4 bladed props and spinners for the mustangs to use for electric motor adaptation (once I get that far).
I have got a Diels Engineering DO 335 (pfeil) arrow, a Golden Age Reproductions P-51 B/C an A Classic Aviation Models (formerly Monogram) Speedee Bilt P-51D kit plus a whole slue of Guillows kits all unbuilt. I'm not going to let any of these go until I copy the plans and duplicate the parts onto fresh balsawood. The mustang and the Guillows planes I'd want to convert to electric, I'd also like to find scale 4 bladed props and spinners for the mustangs to use for electric motor adaptation (once I get that far).
That staggering really looks cool...is it a homebuilt...I noticed it has some balsa wood in it. Anyway, I need the whole set up, the transmitter/controller, plane and all...maybe we can come to a deal. I had intended to build a simple cub in the build tent. I know nothing about foam board and have been building balsa/stick/tissue models all my life. I'll be there Sat and Sunday for sure...I missed out on the campsites so I'll probly be staying at Big Arb's in Minerva.
