Register | Help | Store Account | FliteTest Dashboard
Results 1 to 4 of 4
  1. #1

    Join Date
    Jan 2017
    Location
    Los Angeles
    Posts
    10

    Balsa FT Trainer plus ram air, eliptical wing, and springs

    This plane was the second balsa airframe to carry the electronics from the FT Tiny Trainer. The goal was a comparable flight regime with landing capability.

    Click image for larger version. 

Name:	IMG_5715.JPG 
Views:	1 
Size:	1.84 MB 
ID:	94634

    Click image for larger version. 

Name:	IMG_5656.JPG 
Views:	0 
Size:	1.75 MB 
ID:	94625

    Fuse is box construction. The angled air scoop is of low efficiency, but adds structural rigidity for the castoring nosewheel which will run upward through the airstream.

    Click image for larger version. 

Name:	IMG_5658.JPG 
Views:	0 
Size:	1.38 MB 
ID:	94626

    The nosewheel carrier is a long cube of pine, drilled across the grain to take advantage of high density layers in the wood. Thin pine sheeting was epoxied on the four surfaces to prevent breaking the sensitive cube. The threngthened cube is inserted through a sheet of basswood and balsa fillets finish the surface.

    Click image for larger version. 

Name:	IMG_5662.JPG 
Views:	0 
Size:	1.49 MB 
ID:	94627

    A long strip of pine reinforces the top edges. Holes are predrilled and allow for an adjustable wing position. They are the primary structural element of the fuse.

    Click image for larger version. 

Name:	IMG_5665.JPG 
Views:	0 
Size:	1.26 MB 
ID:	94628

    Pine noseframe ties the pine runners into the frontal nose panels. The pod area is sheeted on top.

    Click image for larger version. 

Name:	IMG_5673.JPG 
Views:	0 
Size:	1.13 MB 
ID:	94629

    Completed nose assembly.

    Click image for larger version. 

Name:	IMG_5683.JPG 
Views:	0 
Size:	1.43 MB 
ID:	94630

    Ribs are cut by clamping between two rib forms.

    Click image for larger version. 

Name:	IMG_5692.JPG 
Views:	0 
Size:	1.83 MB 
ID:	94631

    Tapered wing. Zero sweep allows for a straight spar. The top surface is level, while the bottom surface tapers toward the tip. Chord tapers toward the tip.

    Click image for larger version. 

Name:	IMG_5709.JPG 
Views:	0 
Size:	1.03 MB 
ID:	94632

    I did not make a complete D-tube wing sheet, and the wing twisted easily. For this reason i added geodesic ribs. These ribs do not contact the final tissue.

    Click image for larger version. 

Name:	IMG_5713.JPG 
Views:	0 
Size:	1.79 MB 
ID:	94633

    I decided to maximize the leftover spar tips by tapering them agressively at the tip, then sheeting them with a curved top and a flat bottom. Top sheet first, then sand along the bottom spar tip to achieve planform on the top sheet. Cut bottom sheet to fit. No good pics of this.

    Click image for larger version. 

Name:	IMG_5715.JPG 
Views:	1 
Size:	1.84 MB 
ID:	94634

    Each tail surface is made of two sheets of delaminated foam board that have been sandwiched and sanded. This was glued on lightly as a safe failure point. Despite a small and moderate distance elevator, authority is more than sufficient.

    All up, 200-250 grams. 36" wingspan. Handles easily well into stall region. It handles gracefully but requires constant attention when it comes to roll.

    Videos to come demonstrating the nose spring, ailerons, and flight.

    Oh, and the wheels were made of foamboard with a thin balsa tread. a sturdy hub was made by slapping epoxy/filler composite around a paper tube rolled around the axle. No pics of this either but i plan to make a thread on these incredibly simple, light, thin, but wide-hubbed wheels.

    Feel free to post pics your own builds offering techniques or similar elements.

  2. #2
    Skill Collector rockyboy's Avatar
    Join Date
    May 2015
    Location
    Alexandria, VA USA
    Posts
    3,152
    Congrats on a very cool build!
    I want YOU to join us in the 2018 Flite Test Forum WWII Design/Build Challenge!

    My hanger listing, build threads, conversion projects, and Taranis radio mods are Over Here....

  3. #3

    Join Date
    Jan 2017
    Location
    Los Angeles
    Posts
    10

  4. #4

    Join Date
    Jan 2017
    Location
    Los Angeles
    Posts
    10

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •