electrohub

Sorry to be a bother, two areas I am confused on Electrohub Spider build with RTFQ kits: 1. Was I supposed to solder two of the motor leads flipped to get the twp that spin in the opposite direction, or is it based on the port the ESC's connect to? 2. Someplace, I thought in the FT Build video I...

Hey guys, about a month ago my electrohub had a horrible crash where one of the props broke in mid air causing my quad to faceplant into the ground, lucky for me the only real damaged part were the wooden arms and a few props. now that I rebuilt it, the 8" props that I use look to small compared...

Any chance the FliteTest store might one day carry the carbon fiber booms that David Windestal offers on RC Explorer for the TriCopter? I ordered a set of 4 for my ElectroHub to test out, but it would be nice to be able to get them from here in the states if possible. I know they're only 10mm...

I just wanted to share this little find. I recently built an angled arm racing quadcopter with the electrohub like Eric Monroe's in the Naze32 setup video and really wanted to get a dome to protect the flight control board like the one Eric used. I searched online and couldn't find one with...

Hello all, A couple of weeks ago I purchased the Electrohub quadcopter kit. After watching the videos, it went together very smoothly. After setting up the Naze 32 board I have come across an issue that I hope someone can help me with. I am currently using the featherweight lemon rx receiver...

My ElectroHub Quad (MWC Flip 1.5)has flown successfully but having recently repaired it, I've not been able to fly it. Upgraded to Lemon-RX with Stabilizer. Bound successfully. But, now when hook up battery and turn on TX, cannot activate motors. Lights ok on RX and MWC but no motor...

Hi, I am very much a beginner, and a friend and I just completed an electrohub build. It took a long time troubleshooting various things, but everything thing finally functions for the most part. However, when we take off, the quad starts to spin counter clockwise, somewhat aggressively...

Well, I'm coming back to the hobby. I maidened a plane for the first time in 15 years or so, and I finally got a quadcopter in the air as well. Things are falling into place nicely and I'm starting to question how I was away from this hobby for so long.... I feel like i'm making the finishing...

I just got a new RTF gimbal form RTF quads, but it doesn't seem to work. When I plug my 3s battery into it a solid blue light, and red light come on, and so does a flashing green one. This is my first gimbal so Im kinda lost. Any ideas on why it isn't working? Thanks!

So I've been flying my Electrohub for about a month now and I'm loving every part of it, however about 2 days ago I started hearing a weird noise being emitted from the quad-copter. The best parallel I can give to the sound is when you have a weed wacker spinning at high speed, cutting a piece...

Heya, so I've been flying prebuilts for a while and they were a lot of fun. So I thought I'd take a cheap nose dive into building my own. I purchased the Electrohub, the naze32 acro board, and the power pack that was suggested for it. Figured if I wanted to delve deeper, I'd do that on my next...

Hi folks, I have looked at a heap of posts and cannot find an answer to my problem so I appologise if it has been covered before. I have just completed my first build of the FT Electrohub with the flip 1.5. I am using a turnigy 9x controller and receiver. When I calibrated the esc's they...

I completed my ElectroHub Spider Quad tonight. Had a quick maiden just before dark. Flew great. I used the Altitude Hobbies electronics kit, flip 1.5 controller and my Futaba 6ex. The Batbones is one year old this month with close to 30 hours flight time on it. Thanks Flitetest for designing...

Hello everyone, I am posting this thread to let everyone know that if you damage, break, or don't like to use the wooden booms for electro hub I have a solution. I caded up a design for the spider quads arms. There's 2 pieces, the front arms, and then the back arms. Basically if you have a 3D...

Hello, I'm getting tired of having to take my Blade 350qx3 completely apart to replace any one part. I've looked for aftermarket frames and the only thing I've found is $125. I don't know enough about flight controllers to know if the one in my 350 will support different sizes of frames...

At the suggestion of one of the mods, I am splitting up my previous request thread. The meat of this one is this: There doesn't seem to exist anywhere a good guide to the differences, advantages, disadvantages, and best uses of the various kinds of multicopter configurations. I am considering...

I decided to build the electrohub quadcopter, and I ran into a few problems: soldering iron not hot enough missing XT60 battery connector broke a boom couldn't bind my controller And finally- my motors don't move. Every problem I found was solved, except for motors not moving. I set up the...

I just recently got into quadcopters and I bought my first kit, the Electrohub. I got everything together with some help from some great people on the forums. I went in my backyard and got it in the air for about 10 seconds and landed it now satisfied it would fly. Later that night someone on...

Hey all, I'm getting a parts list together for building my first multi rotor - the FT Electrohub quadcopter. I'm planning to source my motors from Hobby King (EU) to save on import duties and shipping in Denmark. Judging from what other people have reported, and the power kits available...

Hi guys... So I want to build an octocopter based off of the electrohub system, but I just have no clue what batteries, motors, or how to distribute the power. I'd like this heli to be on the small side, maybe 6 or 7 inch props, but I'm not one to scavenge the internet looking for each...