electrohub

I have just got into multi rotors and just built my first kit, the Electrohub. Everything went together fine, but my controller (dx6i and dx5e I tried both) would not do anything (yes i did bind, I'm using a Lemon 6 channel RX). The next thing I noticed was all 4 of my ECS were getting burning...

Hi guys, just bought my first quadcopter, its an electrohub kit, and im in the process of ordering the rtfq electronics, pimped out 1.5 flip, f-30A speed controllers, 4 pack t2212-980kv motors, propellers, harness, receiver cable etc. Should i get a normal lemon receiver? side pin or end pin...

I've got an Electrohub kit with the RTFQuads pack. I flipped over immediately on my first flight. I verified that all the props are spinning in the correct direction and that the inputs to the board are connected to the right inputs on the receiver. What can I check next?

I'm building my first Electrohub kit (with Ready To Fly Quad electronics pack) after building a few FT airplanes. I soldered the motor to the ESC as shown in the video, but I don't have a servo tester to try out the motors and see which way they spin. Instead I just hooked up a receiver that is...

Hi forums, I have finally finished my Electrohub build and need help with arming it. It has the Electrohub kit so the Flip 1.5. I have this for my transmitter http://www.hobbyking.com/hobbyking/store/__15140__Hobby_King_2_4Ghz_6Ch_Tx_Rx_V2_Mode_2_USA_Warehouse_.html. It is bound to the receiver...

Hey guys. I just built my second electrohub (one for my brother). After trying to maiden it and having it inexplicably flip over every time we powered up (turned out to be a gyro calibration issue as wiring, motor direction, props etc were all correct). After getting that sorted I went into...

I received an electrohub kit for Christmas. Over the past few days I have built my electrohub, had my first flight and first crash following an out of control encounter with a tree... 2 broken props and 2 split booms later I decided to check over everything to make sure it was my terrible pilot...

I won't call it a maiden because I have flown this quad quite a bit before this. This is an electrohub with a 2200mah battery. Threw some FPV equipment on it in an attempt to get something working. Quite pleased with the result so far. This is some video footage of that test flight! Hope you...

Please Check out my quad on ebay http://www.ebay.com/itm/111524161124?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

Hi, I am very new to R/C plane/multi-rotors. However, I am very interested in the hobby. After watching many build and demo videos of the Electrohub quadcopter on Flitetest by Josh, I really like the design and decided to buy one (with the camera mount too) - here is the link. I also got the...

Hello, I would like to add fpv to my electrohub and use my fatshark goggle to fly it by. Could you recommend a fpv setup that will work with fatshark goggles. Gopro? Mobius? Camera board? If you could take in to account,.. cost of fpv Ease of setup/support Use of different goggles Displace...

A newbie to the quad building have 5 RTF's 350QX down to the micros. Problem is I ordered this electronics package because it was suppose to be plug and play, and later found out it's that easy... After watching Crash's video Flip 1.5 for dummies and trying to get my computer(iMac) and the FCB...

Hi, I am running a electrohub quad with a 3s 2200 mah battery setup. I added strip LED's to the arms for perspective and to play at night. I think I figured the power usage of the LD's correctly but can someone back me up? The LED's are advertised at 4.8 watts/meter. I have .81 meter (81 cm)...

Hello people of the forums, this is my first time here so i hope you can help my noobieness. I have been building an Electrohub Spiderquad and have been having some problems. I have everything setup, everything plugged in and soldered, i have triple checked. Bound the transmitter and the...

Hello, I have finish my electrohub build with the flip 1.5. My first flight test was not a success. The MultiRotor tip forward and broke one of the propeller. I just received the replacement propeller and I was testing it slowly by adding power to the electrohub a little at a time until it...

So the Electrohub is my first multicopter build and I am new to the hobby. I purchased the package from Whitespy and have the quad ready to go however I can not find any good info that tells me how to set up my Turnigy 9X. There are some videos that walk through the Turnigy 9X with ER9X...

I built an Electrohub up from the show using the kit from ready to fly and I use it for LOS flying to take video. Most of my flying is done in ANGLE mode. I am Using a DX6i radio and AR6210 rx and a 3s 2200 mah battery. Multiwii Flip 1.5 with gps/baro addon. I have balanced the props. I added a...

Sorry I don't have time to explain in greater detail, I'll let the pictures do the talking. All it requires is: -Machine screw, 3mm or 4mm or 1/8" -Matching washer, outside diameter about 12mm, 10mm is too small -Matching lock nut, serrated or nylon -Matching spacer, nylon or aluminum, cut to...

Hello, I am new to quads and configuring the radio. I'm stuck and in need of some help. I bought the electrohub from FT and the electronic package from readytofly that has the flip 1.5 in it. I'm confused how to plug up my hobby king t6a receiver to the flip, configure the correct settings...

So I've finished building my first quadcopter following the Electrohub tutorial and hooked up a Turnigy 9x receiver. It appears to bind to the transmitter successfully, but when I turn it on normally and give it some throttle, nothing happens. The lights on the MultiWii board turn off as soon as...