motor

The good news. We built a foam board plane (thank you Flite Test) RC kit we have. A DX9 Tx (we wanted future options) Spektrum AR610 receiver with remote recevier (belt and braces) Suppo 50A ESC (I figured >A means harder to kill) with BEC a Suppo brushless motor 2814/8. 1000Kv I believe...

The motors on my pumpkincopter are the 2212 1000kv orange cheapies, for now. As I look to upgrade the motors on my XJ470 in the future, the more powerful Multistar cans from that will probably end up on my electrohub (again, pumpkincopter) quad. I really don't want to have all those motors...

Hi! Does anyone have know any good RC plane (beginner park flyer) motors that are around 1,000-1500kv and only need a 20 amp esc? I know Flite Test store has the Emax GT2215 1100kv motor and I thought about just getting that but then I think I'd need a 30 amp esc (Wich is perfectly okay but I'm...

Hi, I am brand new into RC plane, therefore excuse my question. I have a HobbyWing ESC and Turnigy D2826 MOTOR. When I connect the battery to the ESC and motor is also connected I hear a beep 1 per second. I did some research and found out that it could be the throttle to be set but I can...

Hi, i am pretty new to RC flight. I never build ore flew one. Now i am a early retirement guy in his early 40th. And i struggle to get rid of the morning time. I need a Hobby ;) So i ordered a tiny trainer and hot glue gun on Saturday. I cant spend much money so i bought a used Devo 7. I...

Hey everyone, I am trying to get my f330 working, and it seems that the Emax cooling 2208 1500kv motors, were so powerful that they exploded all the 8050 props on my quad. My girlfriend standing about 10 feet away got stabbed with one, and i was literally holding the base of it, and didn't get...

Hi, Can anyone help me with my motor twitching problem? When I give throttle my motor goes back and forth really fast. I am using an 1806 motor (pretty much the same that is in power pack A) and I am using an orange RX with the dx6e transmitter and a 12 amp esc with a 2s. The motor has plugs. I...

I recently assembled the power pod for a Tiny Trainer. Some of the instructions weren't clear and I had tried to attach it using four screws instead of the two it showed in the video which didn't work. I also used the medium sized screws rather than the smallest ones that came with the motor...

At the point when the engine is working, curls and commutator pivot, be that as it may, magnet and brushes don't turn. The substituting curl current is pivoted with the assistance of the engine commutator and the brushes. As the voltage rises, the brush dc engine speed increments as well. The...

I recently was at an auction and got this motor out of an old plane and I want to know what it is. Its not letting me upload the pictures directly so her is a link: http://imgur.com/a/gZ7N1

I recently constructed the FT Flyer and mounted the motor that had been through a crash on my tiny trainer but afterwards still worked. Today when i tested the motor out for the first time on the Flyer, it just like jerks around. The only improvement I have been able to make was to get it to...

Hello, I have an Emax motor and ESC. I can sometimes get the motor to spin up to full throttle, but most times the motor seems to skip and turn only slowly. When I do get the motor to spin up I have to carefully feather the throttle to achieve full throttle up. I have set the start force to...

Hi everyone! This is my first post on this forum, and I wanted to ask a question regarding my Quadcopter. I'm using a 250 frame with a 3 Cell 2250mAH Lumenier battery, and it has 12 Amp BLHeli ESCs, along with EMAX MT2204 KV2300 Motors. As I have only flown this drone for roughly three months...

Hi folks, building my first RC plane – the FT Storch. Not getting very far! Bought the precut kit with the recommended electronics. For the life of me, I cannot figure out how to attach the motor to the power pod. Obviously, the wires in this picture must be stationary. Thus, that part of...

Hello, i Have a problem and hope you can help me. A while ago I flashed BLheli on my Afro 30A ESCs. I then tested one of them with my old Turnigy motor to make sure it wouldn't damage the Motor, did a few tests, looked if the Motor gets warm and so on. Then I flashed BLheli on all my ESCs...

Hey Flitetest, I already submitted a Support inquiry about this but I haven't heard anything in 24 hours now and these things always bother me to no end so I feel impulsive to try and get a response lol. (But sorry if I'm being pushy) My Case number is 43646 Basically, one of my motors on my...

I broke the front right arm on my Eachine Falcon 250 Pro and banged up the motor too, from the sound of it. I have to replace the arm and I am going to replace the motor too. The ESC (all the motors and ESCs are stock) should be just fine and I want to keep it. If I buy a new motor should I...

Hello, I'm new to the hobby and building a Tiny Trainer. Would this be a good motor for it? https://hobbyking.com/en_us/qav1806-2300kv-ccw.html It's already on the power pod, but I figured I'd better ask before the maiden. Will use this prop...

I'm running an emax rs2205 2600kv motor with a 40a ESC on a 3S lipo and 5x4 props, and I'm getting issues with the motor stuttering on low throttle. I tried a 12a and an 18a ESC and had the same issue. Is my battery too low voltage or is my ESC too low amperage for the rs2205?

Hi All My First post here. Like 10 years back I used to make small park flyers from speed 280 and speed 400 motors and now I need to get back in to the hobby. As I have no experience what so ever with brushless motors, I would like to get your advice choosing a motor for models of span...