naze32

Hi all, I'm not really interested in flying in real time. While I like flying, this is a need based problem. What we need is a drone that can survey the planted fields and do an imaging pass (NDVI) to let us know where we need to direct attention. We have some autonomous ground based vehicles...

Hello everyone! I'm new to the Naze32 Board, and currently having issues with my motors. I am running an AfroFlight Rev5 board along with DYS 1806 2300kv motors, Turnigy 10A ESCs, HK6S, and a Turnigy nano-tech 1.3A 3S battery. I am able to arm and disarm the motors using the transmitter...

I recently flashed betaflight 2.7.1 to my FC and now I'm running into a weird issue. The craft now rotates 90 degrees in the other axis after a flip or roll. So once I complete a roll, it will pitch down 90 degrees just after stopping the roll. It will also roll 90 degrees after completing a...

So this is my second 250 class racing FPV quad and I am having a confusing issue while in horizon mode. First off my build consists of: -Diatone Blade 250 frame with integrated PDB (also have tried using a separate PDB on the build) -10DOF Naze32 rev6a FC (have also tried with Naze32 rev5 acro...

The issue I'm having is my versacopter is drifting on liftoff. I have to Compensate on the right stick to correct it. Is there anything I can do to fix this?

Hi, I was looking into buying a versacopter v2 and using the naze32 setup. Before I invest in all of this, I was curious on programming the flight controller. Since I have a cheap transmitter, it doesn't have a screen or any of those types of functions. Just the basic controls with a few toggle...

Just got a quick question: I am trying to flash my Naze32 Rev6 board, but I keep getting the error, "Failed to open serial port." I know utterly nothing about these things, and would really appreciate some help! If needed, I can send screenshots and provide more details. Thanks!

I've recently done a software update on my Naze32 rev 6 and the motors have become out of sync and are spinning up at different speeds however, when inside cleanflight the motors are in sync. I followed all the steps in josh's video and still they are messed up. I am currently using: flite...

Greetings all! My electrohub spider quad was flying nicely with a KK2.1, but I decided to upgrade it to a Naze32. I bought it from here: because I could get a full mag, baro, sonar version, and it was a pretty good deal. http://www.ebay.com/itm/141943462470 Here's my issue, I am not getting...

Hey guys, I recently built my second quad, a QAV 210. I've been trying to tune it and it flies really well actually until I roll or flip it. As soon as I try to do one or the other, it just drops out of the sky. Just wondering if anyone may have any suggestions to fix this problem? I'm using...

I have been flying my Versacopter for some time now and upgraded to the new mounts. I use powerpack E and a 3 cell battery. It flies pretty well and I fly a lot in acro mode now. Sometimes I get some oscillation when I cut the throttle when lowering altitude and I cut the throttle too much. My...

I have a Mac running El Capitan (OSX 10.11) and while I can open up Cleanflight, I cannot get it recognizing the USB port. Here's what I've done: 1. Installed Cleanflight 2. Installed the CP210x USB to UART Bridge VCP Drivers 3. Open Cleanflight From here, there's no option for USB. I've...

So I finally completed my versacopter v2 build using Flitetest electronics pack. The only difference is I am using a dx9 and a lemonrx 8 channel ppm reciever. Used pid setting provided by the video for a baseline(I am a newb tuner). Tried to set the loop time like in the video but no matter what...

I'm in the process of building a Y6 hexacopter following Eric Monroe's video. Parts were purchased from Flitetest. I'm using a Naze 32 rev 6 board. Transmitter is a Spektrum DX6i and AR610 receiver. I'm at the point where I'm configuring the rig following Josh Bixler's video for the Naze 32 rev...

Hi guys I am currently doing my first Naze 32 build, I have connected the Receiver, Esc's and OSD and everything is working. But for some reason today, when trying to connect to cleanflight with a usb cable there is now a problem. The blue light comes on but is very dim and does not connect...

Hey guys, I would normally troubleshoot this myself, but I am a little tight on time. I just flashed CF back onto my naze after running dRonin for a little bit. I had to short the boot pins to get it flashed, but it connects to CF configurator now. First I went back to CF 1.09 because I had some...

I have been working on building up a ZMR 250 and have everything put together and flying now, but I have an issue with the transmitter/receiver that's got me baffled. I set up everything in cleanflight and it seems to be working, but my Taranis is giving no response for the first 20% on the...

What does it mean when you look up the Naze32 and sometimes it is called Funfly? What does that mean?

Hey folks, I've built my Versacopter but I have a hit a bit of a snag with setting it up, here are my specs: Powerpack E Naze32 Afroflight by X8R receiver Taranis Transmitter I've double checked prop orientation, as well as calibrated the ESC's/Accelerometer at least a dozen times now. It...

I'm building a new quad based on the White sheep frame. It's the first time I'm messing with LEDS and not everything goes according to plan :( LEDs are more/less working : they light up, but the colors are all messed up. IMHO, it's definitely a serial sync issue but I don't understand why. My...