naze32

i have recently bought the versacopter off the FT store, and i have ran into lots of problems with the naze32 rev6. one of the most recent problem is that i cant enable oneshot. i have been watching Josh's tutorial on how to setup the naze32 board, when i get to the part went you turn on oneshot...

:confused: my first time ever setting up a control board and I have the naze32 trying to program with clean flight when I follow the video on flitetest I keep getting failed to open serial port. now I was an idiot and got flustered :mad: to the point that I wasn't paying attention when...

Hello all. I am using a Naze32 Acro board with the DX6, cleanflight and a spektrum 6 channel AR610 receiver for a Flitetest Versacopter. I followed all of the directions on the build videos. I flashed the board with the latest firmware. This procedure worked and when I tilt the board the graphic...

Hi everyone...I bit the bullet and decided to try to build my first multi rotor...a versacopter 280 that just came out. I'm brand new to all of this. I've done everything by watching the videos and putting it all together. I'm to the point to configure Cleanflight on my Naze32 board. I get it...

Hi, I've build H-Quad using the scratch build from here http://flitetest.com/articles/H_Quad_Scratch_Build. The only deference is that I have used cleanflight and Naze32 setup. The problem is that I can't find the right and suitable mixing for it.!! :confused: Do I need to select...

Hello everyone. So my roommate and I have been watching flitetest for quite some time now. We have been building many of their planes. I have been looking into a quadcopter for a while and I have been torn on what to get. After seeing the flitetest versacopter recently, my roommate and I decided...

i have had my ZMR250 racing quadcopter for a while now and the 3rd and 4th ESC outputs don't work so i have desoldered those pins and resoldered them onto the 5th and 6th places and the motors spin but i have to set it up in cleanflight asa hex to get it working, i can set it up as a quad...

I've recently built a QAV250 with a Naze32 Acro and Cleanflight. I have had several successful flights with the default settings but it doesn't feel particularly locked in and wind can easily push it around. I've calibrated the accelerometer/gyro and am running 1.9 firmware. I also lowered my P...

Hi, I am making a mini fpv racing 250 size quad but I am having a lot of trouble with connecting the naze32. I connected it to my spektrum receiver correctly but when powered the receiver light doesn't go on, only the naze32 lights go on. And I use this receiver all the time so I am not sure...

Hi Everyone, I wouldn't consider myself a noob with multi's but I am a noob as far as building my own and programming the flight board, which is where my question comes from I have looked around on the forums for a little bit trying to find anyone that has set up a naze32 board for a deadcat...

Help with baseflight/cleanflight/openpilot My new Naze32 board arrived in the mail today for my first quadcopter build but as i go to flash its firmware i discover that its not being detected, i downloaded all my drivers and even tried changing settings in device manager but it turns out that i...

I'm new to the multi rotor scene and have built an electrohub Quad using the dihedral booms and Naze32 board. I originally built with the flip 1.5 and FT recommendations from the build video. I switched to the Naze32 due to the easier setup using Mac computers and Chrome browser. I am still...

Hello, i'm new to soldering and electronics in general so bare with me please. After soldering my pins on the Naze32 the continuity Check Pings between -VBAT Pin and -TELEM Pin. also I get a Ping between all my Motor GND Pins and same is the case with the Motor + Pins (the Signal Pins are not...

******Solved****** I have built my first quadcopter earlier this year and it had been working fine until an ESC died, not knowing if the others would die I purchased a 4-in-1 ESC, the Q Brain 4x20A. so yesterday I got that all mounted and wired up, the motors were spinning the correct...

I've been traveling through my country, trying to get awesome shots from landscapes. With it being a tropical country and all, I am bound to get some rain. At first, I thought it would not be a big deal, because I could wait it out or just fly if it was only mist. But yesterday I almost lost my...

Hi guys. I am fairly new to multi rotors and i could use a bit of help. I built a hovership mhq2 which I learnt to fly on but I have just built a custom frame for aerial photography. The problem I am having is that I have set up everything in cleanflight. All motors and props are correct...

So I had a crash a while back and ever since, my ship has been intermittently bouncing around in the air and feeling very unstable. (I don't know if this particular problem is related to the crash, but I thought I'd mention it.) So I ended up replacing literally every single part in the...

Hi guys, so I'm currently designing my first homemade quadcopter and was wondering which flight control board to get based on what I want the quad to do. I'm building a quad for photography and footage and my camera is a gopro so it will be required to be a stable quad capable of lifting some...

Hello all, I'm tuning my new 450 DYI setup today... here is what I have so far: 1) It is a 450 frame 2) 22-16 800Kv motors 3) 10x4.5 SF props 4) Afro 20A ESC configured with BlHelli 5) Nanze32 Full board 6) OSDoge 7) OrangeRX 433Mhz (yup, I have my HAM license) Here are my current PID...

Hello all, I have an interesting issue where i'd like to use the gimbal mode, but ONLY for the pitch. I have read through sever areas where folks turn on the servo gimbal mode but that moves the four motor controls to slots 3,4,5, and 6. Currently 6 is connected to the OSD on the power and...