naze32

Almost finished! I have been following along with the flite test video tutorial, and everything is working. When I plug the flight controller in to my computer with USB, I can see that my receiver is sending a throttle signal. The minimum is about 900, and the maximum is about 1900. I can get...

Hello all, This is my first build, a QAV250. I am using a friend's DX6i in order to save money for the time being. I purchased an OrangeRx r615x to go with it. The naze32 came in the mail today and I have been following along with Flite Test's Naze32 video. I have done the accelerometer...

i was flying and my dear little miniquad went into failsafe... I managed to get it on camera. Note how the props stop, and then start up again and the quad drifts down. https://youtu.be/_3qvlNCGkP8

My Friend..... His naze32 recently stopped working (he is terrible at troubleshooting). He is insisting that he should spend more money on a Sparky flight controller rather then buying another Naze32. I pointed out that all the top pilots still fly the Naze. What are your thoughts on this...

so I use to fly cc3d but way to many problems so I switched to naze32 It is awesome in angle and horizon mode but when I go in to manual mode or rate as you will say forward is backwards left is right but the throttle and yaw are correct I have searched the web for help but no any thing im...

This is my first quad copter build and so i am very new to all of this. I am using a naze32(full version) and was using cleanflight to set it up. I did manage to start to set it all up without any problems. I managed to assemble the whole quad copter fine and everything seemed to be working but...

I'm using CleanFlight and have two 3 position switch (really I'm using the two dials) on my Taranis setup. I have to switch between the P, I, and D yaw settings and the other to increase/decrease their settings. I'm using PID Controller 3. The problem I'm having is that I have no idea how to...

Well, I'm coming back to the hobby. I maidened a plane for the first time in 15 years or so, and I finally got a quadcopter in the air as well. Things are falling into place nicely and I'm starting to question how I was away from this hobby for so long.... I feel like i'm making the finishing...

Hello all I have been slowly building my first quad, i have been involved with RC cars of all types for many years and this is my first foray into flight, i am using the following: Naze32 propdrive 28 motors hobbyking 20A Multo rotor ESC's Turnigy UBEC Turnigy TGY-I6 RX/TX got it all set up...

I have a custom build Tricopter (using the RCexplorer frame; and most of the recommended build components) Its set up with the Naze32 and Lemon featherlite DSM2 transmitter. I've programmed one of the aux switches for arming/disarming; and a separate switch to toggle horizon mode. The maiden...

Heya, so I've been flying prebuilts for a while and they were a lot of fun. So I thought I'd take a cheap nose dive into building my own. I purchased the Electrohub, the naze32 acro board, and the power pack that was suggested for it. Figured if I wanted to delve deeper, I'd do that on my next...

Ok guys I'm new here but been doing multi rotors for a while now. I decided to go from a naza lite to a naze32 acro. I got everything soldered and did the basic setup like on these guys video and most on youtube. For the lift of me I can't figure out whats going on. Even in rate mode...

Hey, Just a quick note to let you know that my latest flight controller series about the Naze32 is now available on the Painless360 YouTube channel - https://www.youtube.com/playlist?list=PLYsWjANuAm4p47OBBTOo4Xr3lNUc8PFpc In the video series we have videos that cover initial setup, advanced...

Hey guys, ran into a problem with my new Acro Naze32 board and was hoping y'all could help. Quad: Acro Naze32 Multistar Elite 2204-2300KV Multi-Rotor Motor Q Brain 4 x 20A Brushless Quadcopter ESC Gemfan 5040 Multirotor Propellers The Frame is of my own design but is very similar to the...

Just finished my first multi-rotor build. Most everything works great (as far as I can tell being a newb) except that the voltage I am receiving through telemetry is lower than the voltage I directly measure from the battery using a multimeter. My tx displays 2.8v per cell and my multimeter...

First the stats: Naze32 flight controller FrSKY D8R-XP Receiver in CPPM mode Turnigy Plush 18A ESC hexTronik DT750 Brushless 750kv BMS-385DMAX digital servo Now the problem (with a little back-story): I put this thing together around July 2014 some time. First multi-rotor, and things went...

Atas Defiance 265 - An Ultimate Fpv Racer Airframe - Hi guyz, i've been working on this design for a while and now when its done i wanted to share it with you:) The goal was to fuse performance, durability, ease of use and full electronics protection in one compact and functional form...

Hi ladies and gents, I hope you all had a fantastic new year! I purchased the tri kit from David and decided to venture into the Naze32 world and as this is a first for both the Tri and the Naze I'm struggling to lock it in when in Horizon "stabilise" mode. The first thing I did is flash...

Hi everyone Can anyone tell me the PID settings for the yaw axis in cleanflight. I did the autotune and got a yaw P value of 11.1 Want to confirm this is normal or not. Thanks . Chamika

Morning all, Since I'm getting my first naze32 board soon I started researching the firmware options for the board and have made a couple of obseravations. 1. Timecop isn't a friendly person and likes to protect his castle. 2. Baseflight is built for 8 bit processors, the naze32 is 32 bit...