EDF/BDF F16

Splinter189

Master member
Today I started work on a BDF F16. The design is based on a smaller model I had done earlier this year.

Super excited about this prototype. Looking forward to seeing how it flies and ironing out remaining design changes.

Sorry pics aren't in correct order, mobile makes it difficult.
DSC_1916-01 (1).jpeg
DSC_1894-01 (1).jpeg


DSC_1826-01-01_compress53.jpg
DSC_1831-01-01_compress89.jpg

20190912_092955-01.jpeg
20190912_093009-01.jpeg
20190912_103506-01.jpeg
20190912_103459-01.jpeg
20190912_093025-01.jpeg
20190912_103525-01.jpeg
20190912_103506-01.jpeg
20190912_103459-01.jpeg
20190912_104306-01.jpeg
20190912_104259-01.jpeg
20190912_104306-01.jpeg
20190912_110416-01.jpeg
20190912_105954-01.jpeg
20190912_105647-01.jpeg
20190912_112929-01.jpeg
20190912_112020-01.jpeg
20190912_115432-01.jpeg
20190912_114114-01.jpeg
20190912_120010-01.jpeg
20190912_115948-01.jpeg
20190912_115709-01.jpeg
20190912_135431-01.jpeg
20190912_134005-01.jpeg
20190912_140707-01.jpeg
20190912_130255-01.jpeg
20190912_120010-01.jpeg
 

Attachments

  • 20190912_103653-01.jpeg
    20190912_103653-01.jpeg
    3.5 MB · Views: 0
Last edited:

Splinter189

Master member



Built another F16 today...make sure you watch till the end1😎😎

Just like the previous one, I am experimenting with the Ben Harbers BDF. Tons of people are asking about these and asking "are they a replacement for EDFs?" My best answer is, BDFs are going to be a great economical alternative to EDFs on certain airframes. What makes BDFs so affordable is they are built from 2207 drone motors, off the shelf props and 3d printable housings.

I can't even begin to describe how excited I am about what this is going to mean for the @flitetest community😁😁

All the wiring and motor KV seemed OK on yesterday's F16, but it appears that the thrust tube was too restrictive and caused the motor to overheat and lock up. So now we will begin opening the thrus tube up incrementally until the BDF is matched up to the airframe. Its all kind of a guessing game, that what makes this so fun!!!

The F16 I am running today came it out 2lbs 6oz with battery, a couple oz lighter than yesterdays.
There were a few other changes that I made as well. The intake in the airframe is way too small. I was able to add slots right where the skin meets the wing to allow more airflow. A BBQ skewer spanned the two formers to keep the skins from collapsing in. Also added some reinforcement to the canopy and nose section. This will also help with ensuring the shape of the nose turns out better.

Anyway, check out the vid, it was certainly an improvement over yesterday, looks like I need to open up thrust tube a bit more.
20190914_135021-01.jpeg
20190914_112934-01.jpeg
20190914_112615-01.jpeg
20190914_173957-01.jpeg
20190914_172803-01.jpeg
20190914_170440-01.jpeg
20190914_170425-01.jpeg
 

man-bot

Well-known member



Built another F16 today...make sure you watch till the end1😎😎

Just like the previous one, I am experimenting with the Ben Harbers BDF. Tons of people are asking about these and asking "are they a replacement for EDFs?" My best answer is, BDFs are going to be a great economical alternative to EDFs on certain airframes. What makes BDFs so affordable is they are built from 2207 drone motors, off the shelf props and 3d printable housings.

I can't even begin to describe how excited I am about what this is going to mean for the @flitetest community😁😁

All the wiring and motor KV seemed OK on yesterday's F16, but it appears that the thrust tube was too restrictive and caused the motor to overheat and lock up. So now we will begin opening the thrus tube up incrementally until the BDF is matched up to the airframe. Its all kind of a guessing game, that what makes this so fun!!!

The F16 I am running today came it out 2lbs 6oz with battery, a couple oz lighter than yesterdays.
There were a few other changes that I made as well. The intake in the airframe is way too small. I was able to add slots right where the skin meets the wing to allow more airflow. A BBQ skewer spanned the two formers to keep the skins from collapsing in. Also added some reinforcement to the canopy and nose section. This will also help with ensuring the shape of the nose turns out better.

Anyway, check out the vid, it was certainly an improvement over yesterday, looks like I need to open up thrust tube a bit more. View attachment 142685 View attachment 142686 View attachment 142688 View attachment 142689 View attachment 142690 View attachment 142691 View attachment 142692

Hahaha hah!

That boy flys like I do. Push the throttle to the stop then just steer.:eek:

I been waiting to see a battery explode in on of these test vids.

Looking at the framecwork for the motor mount I would make the cross beams thicker and lose the part I assume wraps around the motor.

Quad motors need LOTS of air thru them unlike plane motors that can live with air moving around them.
 

PoorManRC

Master member
That's an EXCITING addition John!!! 😎👋👋👋👋
I worked on those back in the early 90'S. The flight characteristics and Wing Loading are actually impressive, considering that it's a frontline, HIGHLY maneuverable Fighter Jet!
It was designed to be as simple as the F-15 is complicated!! 😯

I really don't understand what exactly a BDF is... But it LOOKS like it could be a viable alternative to power the FT A-10, IN THE Engine Nacelles!! 👍👍

It appears that you've got some REALLY sweet Planes in n the Shop, waiting for final approval and release. 😉
CAN'T WAIT!!!
 

PoorManRC

Master member
.... Maybe an EDF and BDF version could be available, so we can choose according to Budget.

(For me "budget" is a legitimate JOKE!, but I'm dreaming!) 😉