The Coffee Shop - For general discussion

[OliverW]

New project, can anyone guess View attachment 201944

Nice looking air tractor you've got there

 

[BlockerAviation]

Removing the bind plug may help. The receiver also may be struggling to send out input due to it not having a sattelite.

Thanks, I did try it without the bind plug and it didn't make a difference. I've also tried a satellite which worked when I bound it but after I turned it off, removed the plug and turned it back on, it did the same thing it's doing now. I also have a similar rx that I'm running without a satellite so I'm not quite convinced that the lack of satellite is the issue. 🤔

 

[BlockerAviation]

New project, can anyone guess View attachment 201944

Good luck!

 

[Quinnyperks]

Nice looking air tractor you've got there

100 inch

 

[OliverW]

Thanks, I did try it without the bind plug and it didn't make a difference. I've also tried a satellite which worked when I bound it but after I turned it off, removed the plug and turned it back on, it did the same thing it's doing now. I also have a similar rx that I'm running without a satellite so I'm not quite convinced that the lack of satellite is the issue. 🤔

Really odd then. Has it been in any crashes?

 

[OliverW]

100 inch

Awesome. A few weeks ago I drew up a 3 view for a 105" one with a fatter wing chord and thicker surfaces like the ef prototype that never made it to production

 

[Quinnyperks]

Really odd then. Has it been in any crashes?

Have you ever had it in any heat or over voltage?

 

[OliverW]

 

[Quinnyperks]

Awesome. A few weeks ago I drew up a 3 view for a 105" one with a fatter wing chord and thicker surfaces like the ef prototype that never made it to production

Awesome, I only did this version (at-502b) because I didn’t want to have a stall speed lower than the supposed 8 on this one.

 

[Quinnyperks]

I got my numbers and idea from www.Teamduster.com

 

[BlockerAviation]

Really odd then. Has it been in any crashes?

Not that I know of, I got it from a club member a while ago but I'm fairly certain that he never crashed it or ran it over voltage, he was vary particular about that sort of stuff. It also shows no sign of a crash or burn out.

Have you ever had it in any heat or over voltage?

 

[Monte.C]

New project, can anyone guess View attachment 201944

It's hard to tell, it's so small. If you made it a little bigger...

 

[Quinnyperks]

It's hard to tell, it's so small. If you made it a little bigger...

Yeah, should have doubled it, maybe 200” would’ve been better

 

[Matthewdupreez]

@Ratcheeroo where is the cg on your 130% telemaster??
@SquirrelTail where is the cg on the stock telemaster?

 

[BlockerAviation]

Battery's charged and ready for the maiden flight tomorrow. Super excited and nervous!

 

[BlockerAviation]

@Ratcheeroo where is the cg on your 130% telemaster??
@SquirrelTail where is the cg on the stock telemaster?

Just do 33% back of the cord of the wing and you'll be fine

 

[Matthewdupreez]

Battery's charged and ready for the maiden flight tomorrow. Super excited and nervous! View attachment 201973

scary.... 2m props wizzing away, yikes....
oh yes and we want to see some aerobatics.......

 

[Matthewdupreez]

Just do 33% back of the cord of the wing and you'll be fine

yea i just want to find out what the exact position is on @Ratcheeroo 's is so i don't crash........... but 33% probably is a good starting point

 

[BlockerAviation]

scary.... 2m props wizzing away, yikes....
oh yes and we want to see some aerobatics.......

On a 15yr old chopper... umm... I don't think so

 

[BlockerAviation]

yea i just want to find out what the exact position is on @Ratcheeroo 's is so i don't crash........... but 33% probably is a good starting point

Your wing is very standard so I'm very confident that it's with a 1/16"