Menu
What's new
By:
Advanced search…

master build

  1. P-38

    P-38

    Relaxed flying p-38 😃
    • mach1 rc
    • Media item
    • master build p-38 services
    • Comments: 0
    • Album: Mach1 rc
    • Category: Festivals & Events
  2. 100_6185.JPG

    100_6185.JPG

    Strips applied. Almost ready to paint.
    • Jerry_C
    • Media item
    • consealer stips applied ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  3. 100_6184.JPG

    100_6184.JPG

    Strips will be applied here to blend glue seams.
    • Jerry_C
    • Media item
    • ft corsair imperfections master build seam
    • Comments: 0
    • Album: FT Corsair Master Build
  4. 100_6183.JPG

    100_6183.JPG

    Arrows point to scrap paper coated with 3M Super 77.
    • Jerry_C
    • Media item
    • creating tape strips ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  5. 100_6177.JPG

    100_6177.JPG

    Ditto.
    • Jerry_C
    • Media item
    • ft corsair master build same as above
    • Comments: 0
    • Album: FT Corsair Master Build
  6. 100_6176.JPG

    100_6176.JPG

    Checking fit of wing and stabilizers.
    • Jerry_C
    • Media item
    • checking alignment ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  7. 100_6175.JPG

    100_6175.JPG

    Main Wing complete less paint and servos.
    • Jerry_C
    • Media item
    • completed wing ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  8. 100_6173.JPG

    100_6173.JPG

    Leading edges taped down until the glue sets.
    • Jerry_C
    • Media item
    • ft corsair master build taped leading edge
    • Comments: 0
    • Album: FT Corsair Master Build
  9. 100_6172.JPG

    100_6172.JPG

    Holding the bottom wing skin angle until it dries.
    • Jerry_C
    • Media item
    • bottom skin glued ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  10. 100_6171.JPG

    100_6171.JPG

    Having the tape holding the leading edge in place allows to bottom wing skin angle to line up so I can easily fold it back to apply glue to the spar. Much easier than dripping glue into the wing cavity trying to get it where it needs to go.
    • Jerry_C
    • Media item
    • bottom skin ft corsair master build spar access
    • Comments: 0
    • Album: FT Corsair Master Build
  11. 100_6170.JPG

    100_6170.JPG

    Bottom Skin Folded back to apply glue. Note the tape holding it in place. This will allow quick and easy skin alignment after glue applied.
    • Jerry_C
    • Media item
    • ft corsair hot glue application master build
    • Comments: 0
    • Album: FT Corsair Master Build
  12. 100_6169.JPG

    100_6169.JPG

    Aligning the bottom skin and taping leading edge for fast alignment when glue applied.
    • Jerry_C
    • Media item
    • alignment assist bottom skin ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  13. 100_6168.JPG

    100_6168.JPG

    Prepping bottom skin
    • Jerry_C
    • Media item
    • bottom wing prep ft corsair master build
    • Comments: 0
    • Album: FT Corsair Master Build
  14. 100_6167.JPG

    100_6167.JPG

    Skinning the Wing
    • Jerry_C
    • Media item
    • ft corsair master build wing skins
    • Comments: 0
    • Album: FT Corsair Master Build
  15. 100_6166.JPG

    100_6166.JPG

    Building the main wind spars
    • Jerry_C
    • Media item
    • ft corsair master build wing spars
    • Comments: 0
    • Album: FT Corsair Master Build