3d printed

SP0NZ FT Legacy Landing Gear Mount This landing gear mount is designed for the FT Legacy (Founders Plane). I'll add my default printer settings soon.

SP0NZ MiG Exhaust Semi-scale accessory for the Flite Test MiG-3 foam board RC model airplane. Exhaust stacks are designed to be hot glued to both sides of the nose on the MiG-3. Purchase the Speed Build Kits on the Flite Test Store: https://store.flitetest.com/ft-mig-3/ Or, download the...

Merlin Exhaust by SP0NZ Semi-scale accessory for the Flite Test FT Mustang and FT Spitfire foam board RC model airplane. Exhaust stacks are designed to be hot glued to both sides of the nose on the Mustang and Spitfire. Purchase the Speed Build Kits on the Flite Test Store FT Mustang...

SP0NZ STD Firewall This firewall is designed to work with the Flite Test swappable series power pods. Mounting holes are spaced specifically for the Flite Test Power Pack B and Power Pack C motors. Motor attachment is designed for self tapping screws included with these motors. I made the...

SP0NZ STD Control Horn This control horn is designed to work with most standard size Flite Test foam board RC model aircraft. The three push rod holes work with standard Flite Test push rods (.039) or can be drilled for use with E/Z connectors. I increased the thickness from the standard FT...

I've been working on a 3D printed Cub, but v1 had some issues which led to its quick demise. Not wanting to let a good failure go to waste, I took my childhood penchant for destroying model planes to a new level. ;) Check it out...

I'm looking for some input, critique and suggestions on a design idea - The plane's target weight with a GoPro Hero 4, a 3S 3,000mAh battery and supporting electronics is under 45oz Construction will be a 3D printed frame of carbon fiber filled nylon - with two 7.5mm CF tubes through the...

Introduction About a year and a half ago I designed my first RC aircraft. A smaller high wing with a 28 inch wingspan. It was built with the intention to be a slower flying and stable trainer capable of most acrobatics. That was easily constructed with a minimum of foam board and 3D printed...

Feel free to follow me on Thingiverse https://www.thingiverse.com/SP0NZ/about NAME DATE DOWNLOAD LINK FT FPV Split Cube 2017.12.15 FT FPV Split Cube FT Boar Gremlin Frame 2018.01.18 FT Boar Gremlin Frame FT Gremlin Frame by Andres Lu 2017.12.28 FT Gremlin Andres Lu FT Gremlin Frame by...

Hello, Me and my friend designed a EDF jet engine, wich we printed out using a 3D printer. After assembly and testing we came to a conclusion that it is working pretty well. So we decided to build a bigger one. Currently the jet turbine measures 12cm (4.73in) and it is 22cm (8.66in) long. The...

I designed and (3d) printed a small mount for the Spektrum Ultra Micro FPV Camera (SPMVA1100) that I thought others might also find useful. The mount holds the camera and a 1 cell 180 mAh. The mount has holes on the base to accept small zip ties. Additional images as well as the .stl file...

I was recently inspired by mpbiv's build and ImmersionRC's new Vortex and decided to design another quad. As you can see, the design is heavily influenced by the ImmersionRC Vortex. You may also notice it's far from finished. At this point in the project I would like to do something a little...

So hobbyking started selling some new EMax polymer motors that were so inexpensive I had to give them a try. In order to get the most performance out of these motors as possible I decided to design the smallest, lightest quad I could. I included 10 degrees of dihedral since that's a new trend...