1. 278944_fd5fb7cc877c781670f7b7f3b428036d.jpg


    Added a CF spar for strength, made it into a kfm2 wing, fully functional canards, and an octogonal fuse.
  2. Aero_Knight

    FTFC19 VF-1 Foam Valkyrie designed by Carlos AR

    The Plan: (As of 09/18/18 09/17/18) This thread will keep track of my progress as I try to design and build an aircraft based on the VF-1A Valkyrie and two of its specialized modes, the FIGHTER and GERWALK. I have been wanting to try this for years and decided to bite the bullet and put some...
  3. S

    Eagle Tree Vector Motor Redundancy

    Hi Everyone, This might be a dumb question, but I can't find a positive or negative answer. I'm looking at building a Y6 for AP. Can the Eagle Tree Vector handle a single motor failure on a Y6 configuration? Thanks everyone! Sharde
  4. M

    Vectored thrust compatibility?

    Apologies if this has been covered before, but I couldnt find anything on this question: Does the slot in mid-engine planes such as the Vector allow enough clearance to use the vectored thrust firewall accessory in the yaw axis? IT looks to me like there would be very little clearance.
  5. S

    Turnigy 9x v2 and Vector Flight Controller

    Hi Everyone, I've been lurking around for a while. First time poster. I have a question about the Vector Flight Controller + OSD available on the FT store. Is it compatible with a stock Turnigy 9x v2 transmitter? Has anyone tried that? Thank you for your time!
  6. FoamyDM

    Robotech VF-9 that flies, maybe Hovers,

    So I have just Arrived into the hobby and I am Eager to start my first scratch build. this post is just The Mission statement: Stage 1: Build the VF-9 from Robotech I have always been in love with the forward sweeping plane designs. I may have started my career as a draftsman, however I have...
  7. D

    Blunt Nose VersaWing and the Vector Flight Controller - **feedback wanted**

    Hello all, I've been flying multi-rotors only a shot bit, tried a little FPV but recently have really wanted to do some VersWing building and flying... as part of that I also wanted to try the Vector flight controller... so, here is where my question(s) come in: 1) I cannot get the Vector...
  8. S

    The SuperVector

    Not sure if the image was uploaded. But the Super Vector is 33 by 37 inches; features a large sports rudder, reworked elevons, wing end extensions for increased lift at wing tips, wing tip stabilizers for better tracking, KF air foils for increased lift, 3000 KV motor for fast performance on...
  9. P

    Tricopter drift issues

    I made myself a Titan tricopter with a vector flight controller. It flies quite fine and steady but with a few issues. It constantly wants to drift to the right and a little forward and trimming does not seem to help. I have recalibrate multiple times as well so kinda at a lost now.
  10. J

    Help needed with upside down propellers for Y6 multirotor

    Hi everyone! I have just built my first multirotor using an electrohub frame - it's set up as a "Y6". I am using an Eagletree Vector flight controller and the configuration software indicates that the top three motors should spin counter-clockwise and the bottom three motors should spin...
  11. J

    Spektrum DX7 Setup for Electrohub Y6

    Hi there all - I'm new to the hobby and have just built myself an Electrohub Y6 using a Vector flight controller and 8 channel LemonRX receiver. My problem is that I am lost when it comes to setting up my (old, second hand) Spektrum DX7 transmitter. I have managed to bind the receiver to it...
  12. makersam

    Issues Converting for Laser Cutting

    Hi everybody :) I have been lurking in the background of this site for a while and finally got around to actually joining up with forum. Funny that I have time to build/fly planes, but never seemed to get around to getting on here lol I worked in a Maker space a little while back and have...
  13. J

    FT Simple Soarer Speed Build Kit

    Will the vector flight controller fit in this plane and whats the biggest battery i can put in it.