Fight test mighty mini trainer motor/esc issue

[luke1350a]

Hi there, I own the mighty mini trainer and recently I have had a problem with the motor and or possibly the esc. when I first turn it on every thing seems fine, but when I push the throttle above about 20% the motor stops spinning. then once I return the throttle back to 0% it makes the starting up beep beep noise. When i try to increase the throttle the same thing happens once i pass about 20%. Any ideas on what might be wrong? and ways to fix it?
I have a BL heli 12A esc and a Emax Mt1806-2280Kv motor.

 

[mach1 rc]

I had that problem and it was my moter was burnt up and I had to replace it.

 

[The Hangar]

Try calibrating your throttle. With the plane off and the prop off, turn the transmitter on, move the throttle stick to the full throttle position, then power the plane on. The motor should make some beeps then put the throttle stick down. Hopefully that fixes it. If not, let us know. Be sure to do it with the prop OFF though. I’ve made that mistake and it hurts!

 

[luke1350a]

Try calibrating your throttle. With the plane off and the prop off, turn the transmitter on, move the throttle stick to the full throttle position, then power the plane on. The motor should make some beeps then put the throttle stick down. Hopefully that fixes it. If not, let us know. Be sure to do it with the prop OFF though. I’ve made that mistake and it hurts!

Ok thanks, I will try that

 

[mach1 rc]

Try calibrating your throttle. With the plane off and the prop off, turn the transmitter on, move the throttle stick to the full throttle position, then power the plane on. The motor should make some beeps then put the throttle stick down. Hopefully that fixes it. If not, let us know. Be sure to do it with the prop OFF though. I’ve made that mistake and it hurts!

I'll say it hurts I had the end of my thumb cut off before.

 

[luke1350a]

Just tried that and it works great now, Thanks!

 

[K3V0]

I'll say it hurts I had the end of my thumb cut off before.

Ouch! How did you use your tx?!😬

 

[The Hangar]

Just tried that and it works great now, Thanks!

Great! No problem

 

[mach1 rc]

Ouch! How did you use your tx?!😬

Sorry does tx stand for transmitter.

 

[The Hangar]

Sorry does tx stand for transmitter.

Yes - tx stands for transmitter and rx stands for receiver.

 

[mach1 rc]

Yes - tx stands for transmitter and rx stands for receiver.

Ok that's what I thought.

 

[mach1 rc]

Ouch! How did you use your tx?!😬

I had to use my fingers to fly and that ended up causing me to crash my plane.😥

 

[The Hangar]

@mach1 rc how is your thumb now?

 

[mach1 rc]

@mach1 rc how is your thumb now?

It's better but I still have raw feelings in it.

 

[The Hangar]

It's better but I still have raw feelings in it.

That's too bad. What size of prop was it, and was it spinning at like full throttle?

 

[mach1 rc]

That's too bad. What size of prop was it, and was it spinning at like full throttle?

It was a 6 inch prop actually it was probably only at 1 fourth throttle

 

[The Hangar]

It was a 6 inch prop actually it was probably only at 1 fourth throttle

Wow that's rough! How much did it chop off - to the bone?

 

[mach1 rc]

Wow that's rough! How much did it chop off - to the bone?

No thankfully it didn't

 

[K3V0]

I’m sorry that happened! And I’m glad you’re better! Hopefully it feels normal soon