diy

  1. vhandon

    Vultee XP-54 Swoose Goose

    I ran across a video of the Swoose Goose a few months ago and thought “Hey, that would make a cool FT build.” Then I thought “You haven’t built an FT plane in years, and you have never made plans for one.” I was learning to design parts in onshape so I told myself “Take a hike, we’re doing this...
  2. vhandon

    Plane Vultee XP-54 Swoose Goose 1

    Specifications: Wingspan: 42” Length: 40” Flying weight: 22 oz Electronics: C-Pack Battery: 2200 mAh 3S LiPo 4 sheets of FT or DT Foam Board
  3. SP0NZ

    Plane Bloody Rascal 1.0

    Bloody Rascal Based on the FT Bloody Baron and SideWinder designed by Dan Sponholz Design by: Justin Boetsma Plans by: Dan Sponholz This plane came from two places. One was to find a happy middle ground between the swappable Bloody Baron and the built-like-a-tank SideWinder. The power pod was...
  4. SP0NZ

    Plane Foam Wonder "Angel" 1.0

    Foam Wonder The "Angel" Based on the original balsa wood design by Bruce Tharpe Foam Board Conversion by: Dan Sponholz Plans by: Dan Sponholz The Sig Wonder is a classic balsa wood and plywood, gas powered model that was designed by Bruce Tharpe in the early 90's and kitted by Sig...
  5. SP0NZ

    Plane Foam Wonder "Patriot" 1.0

    Foam Wonder The "Patriot" Based on the original balsa wood design by Bruce Tharpe Foam Board Conversion by: Dan Sponholz Plans by: Dan Sponholz The Sig Wonder is a classic balsa wood and plywood, gas powered model that was designed by Bruce Tharpe in the early 90's and kitted by Sig...
  6. SP0NZ

    Plane Foam Wonder "German" 1.0

    Foam Wonder * The "German" Based on the original balsa wood design by Bruce Tharpe * The German variant is not one of the original designs included with the kit Foam Board Conversion by: Dan Sponholz Plans by: Dan Sponholz The Sig Wonder is a classic balsa wood and plywood, gas powered model...
  7. SP0NZ

    Part Foam Wonder Battery Tray 1.0

    Foam Wonder Battery Tray STL Designed By: Dan Sponholz 3D printed battery tray designed specifically for my balsa to foam conversion of the Foam Wonder. This battery tray is optional and gets glued directly to the foam battery tray in the model. The slots are provided for attaching optional...
  8. SP0NZ

    Plane Foam Wonder "Russian" 1.0

    Foam Wonder The "Russian" Based on the original balsa wood design by Bruce Tharpe Foam Board Conversion by: Dan Sponholz Plans by: Dan Sponholz The Sig Wonder is a classic balsa wood and plywood, gas powered model that was designed by Bruce Tharpe in the early 90's and kitted by Sig...
  9. SP0NZ

    Plane Foam Wonder "Standard" 1.0

    Foam Wonder The "Standard" Based on the original balsa wood design by Bruce Tharpe Foam Board Conversion by: Dan Sponholz Plans by: Dan Sponholz The Sig Wonder is a classic balsa wood and plywood, gas powered model that was designed by Bruce Tharpe in the early 90's and kitted by Sig...
  10. flitetest

    Part FT Grumman G-44 Widgeon Water Rudder 1.0

    FT Grumman G-44 Widgeon Water Rudder Design By: David Jester 3D Printable replacement water rudder for the Flite Test Grumman G-44 Widgeon. Print vertical with PLA or Tough PLA (PLA+), 100% infill, no supports, with brim.
  11. flitetest

    Part FT Adventure/Beaver Motor Mount 1.0

    Micro Adventure and Micro Beaver Motor Mount Design By: David Jester 3D Printable replacement motor mount for the Flite Test Micro Adventure and Flite Test Micro Beaver. Print with PLA or Tough PLA (PLA+).
  12. flitetest

    Part FT Nano Flerken Printed Parts 1.0

    FT Flerken Printed Parts 3D Modeled By: Dan Sponholz If you're building the FT Flerken from the purchased plans available from the FTCA, you can print these STL files to help you complete your build. Or save even more time and order the speed build kit here: FT Nano Flerken FT Flerken...
  13. SP0NZ

    Part Dummy Radial XL Mk.II 1.0

    Dummy Radial XL for FT 2814 Designed By: Dan Sponholz This dummy radial engine is designed to work with the Flite Test 2814/1100kv motor. I designed it to add semi-scale detail to your foam board model airplanes. It prints as a single piece with no supports using basic PLA filament. The dummy...
  14. ramarao

    RC Sea Plane Build with Depron

    This is my new scratch build RC sea plane with 12mm depron. Electronics: A2212 - 2200KV BLDC Brushless Motor 30A esc 6x4.5 bullnose propeller 1300mah 3s battery 9g servos Total weight with battery:668g
  15. flitetest

    Part Caddx Ant AIO Guardian Mount 1.0

    Gremlin Guardian Caddx Ant AIO FPV Camera Mount Design By: David Jester 3D printable fixed camera to mount the Caddx Ant AIO FPV Camera on the Flite Test Gremlin Guardian. Suggested Print Settings: Filament: PLA, PLA+ (Tough PLA) Layer Height: 0.2mm Supports: None Rafts: None...
  16. flitetest

    Part FT Master Series F-18 Super Hornet Ordnance 1.0

    F-18 Super Hornet Ordnance Design By: John Overstreet Want to load out your Flite Test Master Series F-18 Super Hornet? Look no further. Master Series designer John Overstreet has created a collection of accessories for you to download and print on your 3D printer to make your F-18 look...
  17. SP0NZ

    Part Dummy Radial Mk.II 1.0

    Dummy Radial 9 Cylinder Engine STL Designed By: Dan Sponholz This dummy radial engine is designed to work with the Flite Test Power Pack B/C Pack Radial motors. I designed it to add semi-scale detail to your foam board model airplanes. It prints as a single piece with no supports using basic...
  18. flitetest

    Part Insta360 GO 2 Guardian Camera Mount 1.0

    Insta360 GO 2 Camera Mount for FT Guardian Design By: David Jester 3D printable camera mount for the Insta360 GO 2 designed to be mounted on the Flite Test Guardian multirotor frame. Print Settings: Filament: colorFabb LW-PLA (Light Weight PLA) Flow: 55% Nozzle: 230° C Infill...
  19. flitetest

    Part FT Caddx Ant AIO Mount 1.0

    Caddx Ant AIO FPV Camera Mount Design By: David Jester 3D printable adjustable camera mount for the Caddx Ant AIO FPV Camera. This camera mount requires: [2] 3mm x 8mm screws and [1] 1" x 3/32" O-ring to complete the assembly. Files: Caddx Ant Mount Part 1.stl Camera Plate Caddx Ant...
  20. flitetest

    Part FT Legacy Landing Gear 1.0

    FT Legacy V2 Landing Gear Design By: David Jester 3D printable landing gear mounts for the Flite Test Legacy V1 and V2. They can also be used on other aircraft models by adjusting the length of the joiner wires. These mounts are designed to use Ø .125 inch wire for the main gear, and Ø 3mm...