• This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn more.

quadcopter

  1. DutchRC

    My top-3 favourite 2018 FPV Quads :) - What are your favo's??

    Halloa guys & girls :) 2018 is nearing it's end so I thought I'd answer a question I get asked a lot: what is your favo drone?? I have flown a lot of quads this year, so it would seem like a difficult pick between them? It was actually surpricingly easy though I did pick 3.. Here is my Top-3...
  2. BlueK

    FPV Cloud Surfing | GoPro Hero 7 Black Hypersmooth!?

    Cloud Surfing with my quadcopter, it was a super windy day but a good test day for my my new gopro7 the hypersmooth stabilisation works good but not perfect you can see some glitches
  3. Snarls

    Endurance Quadcopter Build-Off

    This is going to be a fun one. For once, I am not dealing with maximizing acrobatic performance, speed, or camera stability. No, this time it is just that: time. Flight time specifically. My friend challenged me to a build off. Who can get the longest flight time from two 18650b batteries...
  4. G

    Help! Motor 2 spinning faster than the rest on KK 2.1.5 board

    Hey guys, I am building my first quadcopter using the KK 2.1.5 board (the frame is similar to DJI F450, using 1000Kv motors, 2200Mah 11.1v battery), but the motor connected to the 2nd ESC slot on the KK board is spinning faster than the rest. i.e with like around 5%-10% throttle I am able to...
  5. War Chest

    < C O L O R B L I N D >

    Managed to eek out a few editing twists in this video
  6. J

    Motors Spinning at Different Speeds

    I've been working on my new 250mm quad, and when I use the manual motor control in Betaflight, they all spin at the same speed. However, when I go to use the transmitter, they all spin at different speeds. I've tried calibrating the escs and that didn't work. I've included a screenshot of the...
  7. J

    Quadcopter Motors Not Spinning

    I just finished building my first 250mm quad and I armed the motors, but they won't spin. I've tried calibrating the escs, but that didn't work. When I calibrate them through Baseflight, they beep at the top of the slider, beep at the bottom, then continue beeping consistently. I tried using...
  8. R

    Help Needed with custom brushed micro setup

    My intial question: How do i get my motors to react to my stick movements?:confused: This may be a long shot but i was wondering if someone could help me trouble shoot this last problem i have before i can get my brushed micro in the air. I am using Flysksy FS-i6 with a flysky receiver, they...
  9. kpixels

    How To Crash A Homebuilt Multicopter

    Quadcopters And Tricopters Crash Compilation Crash compilation from several years of building and flying. Watch various quadcopters and tricopterst falling from the sky in crisis.
  10. kpixels

    450 Quadcopter Frame From PolyFlex Pressure Pipe

    This $4 frame has no screws, is very rigid and weighs less than the flamewheel. The ESCs are inside the 1" arms/tubes which is more durable and reduces the drag. Illuminati flight controller with on screen display, Xiaomi Yi camera, 600 mw video transmitter, 2212/920 KV motors, SimonK 30 amp...
  11. A

    high voltage brushless motors

    I was wondering what it takes to change the voltage from a normal 6s capable motor to a higher voltage one, something like 10s. This is for a mini quad (250) experiment. I don&#8217;t think that it&#8217;s the size of the wire, because that is regulated by current. But, I may be wrong. Any ideas?
  12. CONNXT248

    Been flying micro quads for a while. Ready for an upgrade.....

    Hey all. So I'm decently experienced with multirotors. I've gone through at least 4-5 micro quads in the past year zipping them through my house, and I've logged a decent amount of time on simulators. I have a 250 size carbon fiber "racing" quad that I bought a few years ago, but I was...
  13. menachg

    need advice on choosing diy plans for quad frame

    hey guys its great coming back here after a few years without serious building in the hobby for me i have a lot expirience in fixed wing and scratch builds and i like this aspect of how flitetest used to be all about taking day to day materials and construcing them into a working flying frame. i...
  14. BlueK

    long/midrange quadcopter mountain diving

    did the last couple of weeks a lot of long or better midrange flying here in the alps and i like it! so maybe this video belongs here too :cool: have fun and fly save
  15. L

    A Little Problem with my First 250 Quad Build...

    Sometime last winter I decided to attempt to build a 250 racing quad. I'm a high school student, so I don't have much time to devote to this project, which is part of the reason it has taken me so long to get to the point I'm at now. So far I've encountered some pretty frustrating difficulties...
  16. S

    Propellers spin then the drone cuts out

    Hi All, I'm a noob to quadcopters/drones and dont really know where to start when problem solving. I have a Syma X5SW-1 and have managed just one flight. The day after this success i powered it up again pushed the accelerater forward to find the propellers would spin for about a second then the...
  17. S

    Propellers spin the drone cuts out

    Hi All, I'm a noob to quadcopters/drones and dont really know where to start when problem solving. I have a Syma X5SW-1 and have managed just one flight. The day after this success i powered it up again pushed the accelerater forward to find the propellers would spin for about a second then the...
  18. S

    Extra motors, multiengine projects

    The motors on my pumpkincopter are the 2212 1000kv orange cheapies, for now. As I look to upgrade the motors on my XJ470 in the future, the more powerful Multistar cans from that will probably end up on my electrohub (again, pumpkincopter) quad. I really don't want to have all those motors...
  19. C

    Foxeer Monster V2 OSD voltage not working

    I have a Foxeer Monster V2 and it works great, but now I would like to set up the voltage meter to display on the OSD. It came with an input labeled "VSEN" and the wire attached was just a bare wire at the end. I read somewhere that if I was using the 12v pad to power my camera (which I am) I...
  20. G

    Flying through a hole in a cliff in Dorset UK - Beautiful

    One of the guys on the Herts FPV facebook group decided to go to the seaside and film this lovely sequence - enjoy - > https://www.youtube.com/watch?v=mtM9lkSEWLc