telemetry

I’m trying to set up voltage telemetry on a plane build. I have the FT 40a BLHeliS ESC, RM ER6 Receiver, and (maybe not as relevant) RM Pocket transmitter. Not sure where to connect a wire to enable this telemetry. Info on the receiver implies this is possible without extra voltage sensor, but...

Good day. Has anyone tried to output telemetry from the Radiomaster TX16S remote to the computer console through software development? I've developed this code, but it hardly reads anything. The remote is equipped with a TBS Crossfire Micro TX V2. Maybe someone has tried to develop this...

hi there flight test hive mind! i'm new to the hobby, just build a tiny trainer with my daughter, gona maiden it today, chuck glider at first. i did just try out the controlls and i works!!! now to the technicals. power pack A in the Uk is from Graupner, it comes with an Ultra control 20a...

So I powerlooped on an extremely flat battery (stupid) and couldn't pull out, so I plopped down relatively lightly in the grass. I didn't lose telemetry (lua, voltage, ex.), but the fc is getting no sbus signal. Connections are all good. I tried a different receiver, no luck. I also tried to...

I recently got the telemetry logging to work on my Taranis Plus and was excited to see how many Gs I was pulling on hard turns with my racing quadcopter. Unfortunately, the accelerometer data is not scaled properly, it is responding correctly to movements, but the resting z-axis force is...

I just finished building a QAV250 with a Naze32 rev6 with Cleanflight and a Taranis X9D Plus with a X4R RX. I have everything wired together correctly, as I can receive telemetry and see the control inputs in the configurator sometimes. The problem is that, when I have telemetry and softserial...

Hello! Recently got into ghe hobby by buying an E-flite Apprentice w DX6, works great, but now awaits spare parts (note to self: do not attempt inverted flight on low altitude on day 2). Anyway, I am thinking of two additions for my Apprentice: 1. Telemetry in my radio, in order of priority...

Hello!! I have a question about the FrSky sensors and the their use in the chain. With the smart port sensors can you have 3 x FrSky SP-FLVS - Smart Port Lipo Voltage Sensor checking the voltage of 3 different packs? I was not sure if you can run multiple or if you can only have 1 type of...

I can't get the telemetry working with my setup. I have set up the KissFC with the receiver as the KissFC manual said and have the receiver type set to "FrSky SBUS" in the Kiss Chrome App. When I discover new sensors on my taranis I only get SWR, RSSI, RXBatt and A2. According to the manual...

Good day all. I am building a quad and would like some feedback on the Frsky sensors like the Variomiter or GPS. As well as the Naza M v2 sensors like the motor temp and other sensors. Figured installing them during the initial build would be better than build and hack.

How high can you get a multi rotor to fly? Anything goes, GPS, radio control, timer, don't matter. Get it as high as you can and prove how high it went with telemetry or video. Can you beat a rocket? Do it.

Hi, first post in here and here goes ... I'm new in the RC community and I'm in the process of sketching up components to build my first 250 FPV quad. Plan is to build quad and fly it and after some time (when the wallet allows it) buy some FPS gear and continue from there. I have nothing at...

Found this article here: http://flitetest.com/articles/Adding_bluetooth_to_FrSky_DJT_DFT_telemetry_module Tested it with my Turnigy 9X, Frsky DTJ + D8R-II and a HC-06 bluetooth module with integrated Max 232. It works and AD1 and AD2 are displayed/read aloud by the FrSky Dashboard app on my...

I'm pretty new, and a lot of you may know this about the Turing 9x. I made a discovery while trying to figure out how to get into the setup to enable an auxiliary channel so I could control a servo on my hex to cary and drop cargo. If I press the up or down button on the main screen...

Just finished my first multi-rotor build. Most everything works great (as far as I can tell being a newb) except that the voltage I am receiving through telemetry is lower than the voltage I directly measure from the battery using a multimeter. My tx displays 2.8v per cell and my multimeter...

forgive me If I R Dumb , I'm new here. Please help point me in the right direction. I've finished building my Electrohub but it's running a multiwii flip 1.5 and i'm using my balance lead from my battery for FPV, so i have no happy easy way to monitor my voltage! So I'm thinking the only...

Hi all. I just finished my build of a 500mm spider quad and had a maiden flight in the snow. The flip 1.5 FC works pretty good right out of the box, but I want to change some throttle and yaw curves and adjust the PID a tad. The problem is, access to the boards USB is blocked by other...

Good afternoon everyone. I've been chatting it up with Bruce Dally at Ubuyadrone.com. Now I don't know Bruce personally but I do know that he runs a little online hobby shop based out of Florida, and I also know that he has secured a number (35 i think) of Taranis X9D Plus, transmitters and is...

I'm thinking about getting a different transmitter with telemetry built in mainly so I can stop setting the low voltage alarm on my quadcopter and let the TX do it for me. I'm interested in the low voltage and an altimeter. Other monitors would be nice but that is all I really want to start...

I have a 2.4GHz FrSky transmitter and receiver combo and a 915MHz telemetry module from 3DR. After plugging in the telemetry module, I noticed a twitch in the tail servo on my Tricopter. It twitches every 1 second or so in a little pattern. like T-T-T--T--T-T-T--T... T stands for twitch, wasn't...