3d print

Gremlin Guardian Caddx Ant AIO FPV Camera Mount Design By: David Jester 3D printable fixed camera to mount the Caddx Ant AIO FPV Camera on the Flite Test Gremlin Guardian. Suggested Print Settings: Filament: PLA, PLA+ (Tough PLA) Layer Height: 0.2mm Supports: None Rafts: None...

F-18 Super Hornet Ordnance Design By: John Overstreet Want to load out your Flite Test Master Series F-18 Super Hornet? Look no further. Master Series designer John Overstreet has created a collection of accessories for you to download and print on your 3D printer to make your F-18 look...

Insta360 GO 2 Camera Mount for FT Guardian Design By: David Jester 3D printable camera mount for the Insta360 GO 2 designed to be mounted on the Flite Test Guardian multirotor frame. Print Settings: Filament: colorFabb LW-PLA (Light Weight PLA) Flow: 55% Nozzle: 230° C Infill...

Caddx Ant AIO FPV Camera Mount Design By: David Jester 3D printable adjustable camera mount for the Caddx Ant AIO FPV Camera. This camera mount requires: [2] 3mm x 8mm screws and [1] 1" x 3/32" O-ring to complete the assembly. Files: Caddx Ant Mount Part 1.stl Camera Plate Caddx Ant...

FT Legacy V2 Landing Gear Design By: David Jester 3D printable landing gear mounts for the Flite Test Legacy V1 and V2. They can also be used on other aircraft models by adjusting the length of the joiner wires. These mounts are designed to use Ø .125 inch wire for the main gear, and Ø 3mm...

Dummy Radial 9 Cylinder Engine STL Designed By: Dan Sponholz This 9 cylinder dummy radial engine is designed to work with the Flite Test Power Pack B/C Pack Radial motors. I designed it to add semi-scale detail to your foam board model airplanes. It prints as a single piece with no supports...

Baby Baron Wall Mount Designed By: Dan Sponholz Designed to fit the Baby Baron, and Baby Brit (also works for similar sized aircraft). Designed to attach to a wall using #8 coarse thread drywall screws. Other sizes available upon request. Print Settings: Material: PLA+ (eSun) Layer...

FT Mighty Mini Pietenpol Model A Engine STL Files Designed By: Dan Sponholz This model is designed to be a 3D printed accessory for the FT Mini Pietenpol RC foam board airplane designed by Josh Bixler of Flite Test. Josh designed a Model A engine for the Pietenpol using Flite Test foam...

Mini Firewall STL Designed By: Dan Sponholz 3D printed firewall for use with the most Flite Test Mighty Mini series models. This firewall is designed to be used with the FT Power Pack A and Power Pack F motors. It will also support any motor with a 16mm x 19mm bolt circle for direct mount...

Servo Mount 9g Double STL Designed By: Dan Sponholz 3D printed double servo mount for use with most 9g servos. Makes servo replacement easy and convenient using the included servo mounting screws. Print Settings: Material: PLA+ (eSun) Layer Height: 0.20mm Supports: None Rafts...

Servo Mount 9g Single STL Designed By: Dan Sponholz 3D printed single servo mount for use with most 9g servos. Makes servo replacement easy and convenient using the included servo mounting screws. Print Settings: Material: PLA+ (eSun) Layer Height: 0.20mm Supports: None Rafts...

Mini Control Horn STL Designed By: Dan Sponholz 3D printed control horn for use on most Mighty Mini-sized FT models. Print Settings: Material: PLA+ (eSun) Layer Height: 0.20mm Supports: None Rafts: None Infill: 20% Grid Perimeters: 2 Top Layers: 5 Bottom Layers: 4

Standard Swappable Firewall STL Designed By: Dan Sponholz 3D printed firewall for use with the most Flite Test Swappable series models. This firewall is designed to be used with the FT Power Pack B and Power Pack C motors. It will also support any motor with a 16mm x 19mm bolt circle for...

Short Control Horn STL Designed By: Dan Sponholz 3D printed control horn. I designed this control horn specifically for my balsa to foam conversion of the Foam Wonder. This control horn will be practical for any foam board model with narrower control surfaces typical on older balsa model...

Standard Control Horn STL Designed By: Dan Sponholz 3D printed control horn for use on most standard/swappable-sized FT models. New updated design for 2022. Print Settings: Material: PLA+ (eSun) Layer Height: 0.20mm Supports: None Rafts: None Infill: 20% Grid Perimeters: 2...

FT Simple Scout XL Gear Plate STL Designed By: Dan Sponholz 3D printed gear mounting plate for use with the FT Simple Scout XL. This plate is designed to be used as a reinforcement for the foam board landing gear tab on the Scout XL. Assembly is similar to the FT Tutor landing gear. Reference...

FT Simple Scout XL Firewall STL Designed By: Dan Sponholz 3D printed firewall for use with the FT Simple Scout XL. This firewall is designed to be used with the FT 2814-1100kv motor. It will also support any motor with a 19mm x 25mm bolt circle for direct mount, or 44mm X-mount bolt circle...

Bloody Baron Wall Mount Designed By: Dan Sponholz Designed to fit the FT Bloody Baron, Bloody Brit, and SideWinder (also works for similar sized aircraft). Designed to attach to a wall using #8 coarse thread drywall screws. Other sizes available upon request. Print Settings: Material...

FT Flerken Printed Parts 3D Modeled By: Dan Sponholz If you're building the FT Flerken from the purchased plans available from the FTCA, you can print these STL files to help you complete your build. Don't have a printer? No Problem. You can order the plywood parts from the Flite Test Store...

A couple of years ago I built a Cartoon A10 from foam. It had a real basic wing with no real aerodynamics to it but some how it flew awesome after some adjustment. I believe the plans came from here. https://www.rcgroups.com/forums/show...=a10%20cartoon This year I got a 3d printer and...