bec

Hi Folks- back to the hobby after a 40 year break! I'm having troubles with the ESC supplied with the Flite Test "power pack B" (it's labled 35A / BEC 3A 5V / LIPO 2S-4S). I've got a Tattu 1300mAh 45C 3S battery. The issue is that when I connect the battery to the ESC, I get the full...

My brother picked up parts from an engineering class at UCI. 2300KV cobra motors, props, and a naza lite flight controller. Apparently, the naza lite is powered by the PMU, so I was wondering if I get 30 amp simonk esc with BEC, can it power the FC or are all the positive wires that go in the FC...

Hey. I'm building my first quad (FT 210 frame) and plugged in my naze and it works fine. I noticed that when I plugged in my Lipo the board gets to around 125 degrees in about 7 seconds before I unplug it afraid that I'm going to fry the board. I have checked that all solder joints are...

Hello, PS : sorry for my english, i'm french :) I had built my first quad with this pack : https://hobbyking.com/en_us/multistar-afro-combo-pack-2206-baby-beast-v2-motor-and-12a-afro-esc-set-of-4-cw-ccw.html?___store=en_us and a CC3D. I've recently changed my ESC to use a 4 in 1 racestar ESC...

I am making a twin motor micro triplane with micro quad motors and 6 amp escs. I want to use a bec but the escs I have don't have the red wire required. I still need to keep things light so how should I power the receiver?

Like a lot of the posts I've seen, I am interested in 250 racing quads. I recently purchased a Carbon Fiber frame from a local shop, and have mounted the motors. I'm now looking to add the ESCs and trying to understand the necessary steps involved when setting them up. It's like drinking from a...

I bought: 1quanum falcon quad frame 1 afro 12a esc !!! Oops! 4 multistar motors 1 orange rx 4channel with 6channel ppm and a naze32. My1st quad... I realized my mistake and went to the local hobby shop and bought 4 hitec 12a multi rotor esc WITHOUT bec. My second mistake/oversight. Short of...

Hi All I have Flip32+ FC (flight controller) connected to 4 OPTO ESC (DYS SN20A). I have one "3A UBEC Module Low Ripple Bluesky". Powering the FC was an easy task, I have just plugged the "UBEC 5v out" to one of the free motor pins. Now I need to connect 2 more elements: 1.12 WS2182b LEDS (12...

Hello, I have a question about the ESC that you provide in the https://store.flitetest.com/power-pack-d-standard-quadcopter/ powerpack D for quads ? Do they all have a BEC ? Is it better if only one of them as a BEC ? Can we remove BECs ? What is UBEC ? And another question : are the...

Hey Guys, I would like to just say, i got a quad back of 30A ESCs from Rotorgeeks which flew well, however the on one with the bec, the bec didn't work, (it should be noted the ESC still took signals from the Naze fine). I exchanged a few emails to David Klein in customer service, where he...

I purchased a Suppo 3A External BEC since my ZTW Spider 20A OPTO ESC's don’t provide power. Since this is my first Quadcopter build, I want to make sure I understand how to connect the BEC correctly. Could I take M1 ESC and pull the signal wire out and plug that single wire into the BEC and...

Hola! Does anyone know what the best 30A ESC's are with 5V BEC? I was looking at Lumenier's, but could not find a lot of feedback. Preferably something available on Amazon.com. Thanks.

I want to know if I can power a receiver with an ESC with a BEC built in without connecting a motor. Is the motor required or does the BEC just split the voltage from the battery and regulate it? If not then how do gliders have their receivers powered? Would a Turnigy Plush 6A ESC with 5V, 0.8A...

Hey guys, so I've asked around and got a few different answers, but can you plug four 15 amp multistar ESC's (switching BEC's) straight into the KK2.1.5 (HC)? Or do you need some 'remove red wire' disabling shenanigans? Cheers.

Hey guys, Ill gonna make myself thrown into the hobby and gonna take my dad back with me so my questions will be about "modernizing" or "old and new" items used together. ( ill post pics of all the material i have ) So my dad is going to prepare his stuff to fly glow and a rebuilt glider. My...

After some kind guys on here talked me down from a 2200KV motor for my first plane (FT Swappable Trainer with 4 servos), I now have a NTM Prop Drive 28-26 1200KV in my sights for it. I'm part way through the build, and also have a Versa Wing cut out! I would like to use a Turnigy 30A Plush 2A...