cleanflight

Hi All, Thanks first of all for all you do to get us newbs up in the air! I am building my second quad from scratch this time. I used the mini racing quad power pack for electronics with a Naze32 Acro and a homebrew H frame. I built a tether that supplies 12.6V/30A to an XT60 plugged into the...

Hi all, I am not able to find the yaw reverse options for the tail servo in Cleanflight 1.1.0 configurator, has anybody had the same problem and resolved it? I feel my options are in CLI somewhere. Thanks in advance.

Hi there I just receive my new Versacopter and Naze32 board and have tons of problem with it. Firstly, Cleanflight kept giving the message "GITHUB Query Failed: API rate limit exceeded for 220.255.227.18". Secondly, when I tried to flash the firmware, it gave a message "No response from...

Hi everyone i just bought the new Versacopter, and i have the naze32 inside for the FC, but when i go to fly it it takes off and flips backwards. I have read a ton of forms saying to set up the naze32 into horizon mode instead of acro mode, but i can't find the setting to do that. I have already...

Hello all. I am using a Naze32 Acro board with the DX6, cleanflight and a spektrum 6 channel AR610 receiver for a Flitetest Versacopter. I followed all of the directions on the build videos. I flashed the board with the latest firmware. This procedure worked and when I tilt the board the graphic...

Hi everyone...I bit the bullet and decided to try to build my first multi rotor...a versacopter 280 that just came out. I'm brand new to all of this. I've done everything by watching the videos and putting it all together. I'm to the point to configure Cleanflight on my Naze32 board. I get it...

Hi, I've build H-Quad using the scratch build from here http://flitetest.com/articles/H_Quad_Scratch_Build. The only deference is that I have used cleanflight and Naze32 setup. The problem is that I can't find the right and suitable mixing for it.!! :confused: Do I need to select...

I've recently built a QAV250 with a Naze32 Acro and Cleanflight. I have had several successful flights with the default settings but it doesn't feel particularly locked in and wind can easily push it around. I've calibrated the accelerometer/gyro and am running 1.9 firmware. I also lowered my P...

Last week I broke two frame arms. Yesterday, I got a new frame, and put everything together again. The same motors, the same ESCs, the same flight controller, the same everything (except for the frame). This time I decided to rotate my flight controller 90 degrees, pointing right, for ease of...

I have this "issue" where I have to push my travel adjustment on my sticks almost to max (~120% out of max 125%) to get them up to 2000 and down to 1000. Am I doing something wrong? Should I be tweaking this somewhere else? It flies well even without these settings, in theory, but I've never...

So I had a crash a while back and ever since, my ship has been intermittently bouncing around in the air and feeling very unstable. (I don't know if this particular problem is related to the crash, but I thought I'd mention it.) So I ended up replacing literally every single part in the...

Hey guys, Just finished my Electrohub Tricopter and had a problem with the tail servo and gyro being reversed. The servo tab in cleanflight had a Normal/Revese setting but it would not save when I changed it to reverse. After a little Googling I found this and it worked for me. under the CLI...

Hello all, This is my first build, a QAV250. I am using a friend's DX6i in order to save money for the time being. I purchased an OrangeRx r615x to go with it. The naze32 came in the mail today and I have been following along with Flite Test's Naze32 video. I have done the accelerometer...

i was flying and my dear little miniquad went into failsafe... I managed to get it on camera. Note how the props stop, and then start up again and the quad drifts down. https://youtu.be/_3qvlNCGkP8

I have a custom quad-x setup. It's setup with a Naze32 acro, Futaba R3008SB RX and Futaba 10J TX. My Naze32 is flashed with the latest stable version of Cleanflight (v1.8.1). So far I haven't successfully been able to arm my quad. I have tried increasing the end points on my TX with no luck and...

Here is a Naze setup that I would like to show every one. Its a flip32+ with Bluetooth and a Spektrum satellite receiver. Some things to note are that the flip32 stock does not work with the satellite plug. You have to fix the board or use a special plug. This fix uses the gps rx pin so if you...

Hey Guys, I'm in the laborious process of tuning my QAV 250 and need some advice from the guru's. I'm pretty happy with the flying characteristics for PID Controller 0 and had NO luck with PID Controller 1 but with Controller 2 (Floating point) I am actually quite happy with the exception of...

Morning all, Since I'm getting my first naze32 board soon I started researching the firmware options for the board and have made a couple of obseravations. 1. Timecop isn't a friendly person and likes to protect his castle. 2. Baseflight is built for 8 bit processors, the naze32 is 32 bit...

Thanks everyone who guided me on my project. I am starting a new thread because the finished design is so different that what I started with. If you want to see how it started out, see the below linked threads: http://forum.flitetest.com/showthread.php?10232-Naze32-V-Tail-Quad-Setup and...