cleanflight

Hi I have recently bought a DJI and after getting good shots and film with it soon wanting to get the next buzz. After being out with a friend who flies a QAV180 i soon knew I wanted one. this is where the problem has started. I have a NAZE 32 REV 6 Flight Controller, have gone into...

i have been fighting an ongoing battle with my Naze32 Rev6 and its uncanny want not to fly. i had my FT210 flying not to long ago and damaged my Video transmitter and was grounded while a new one was shipped. after putting everything back together i decided i would update to the newest Firmware...

i have two naze32 rev 6 boards, one new never flown and one that has been used before. they are both having the same problem. when you hook them up USB only everything seems fine, you can flash firmware and change pid save and reboot no problems. however when you want to calibrate the esc as...

Please watch my video and help me. Thank you in advance.

hello all, I have 2 Naze 32 boards V6, one brand new and one with heavy use. the issue im having is when i connect the board to clean flight everything works, i can flash software i can change PID's however as soon as i connect my lipo battery everything freezes. i am unable to calibrate my esc...

Hello, first time posting! As the title states I started my versacopter build over the weekend and when I went to test the motors in clean flight I get error beeps (I assume that's what they are...). Also I ordered the versa kit with the new "better" e-pack motors, maybe that's causing the...

Well, it's me again... I've got a new problem with my 230mm quad... First of all, I got it flying for like 4 minutes yesterday, which is good, it flew pretty well. When I tried it later that day again it started showing some weird behaviour: When I arm it, the motors start spinning at minimum...

Hi everyone, I'm new to this forum and sadly the first thing I have to contribute is me bugging you with a problem that I have with building my second quad (a sub 250 quad). The quad uses a Naze32 flight controller (Revision 6), 4 x 12 Amp Afro ESCs, 4 x MultiStar Elite 2300KV motors and a...

Hi The guilty truth - I got myself into this mess by doing a probably unnecessary reboot of my FCboard...I was frustrated and wanted to start over. Anyways, here's my situation: I'm using cleanflight and a naze32 REV6 By shorting the boot pads on the naze and using the "no reboot sequence"...

hello! im just testing every thing out before i finally put every thing together ive got the ESC's connected to the F3 via the servo ports and since it states in the manual, to configure the servo ports before use - i just incrementally set the according channels in the servo tab of...

hello! any one ever tried or looked into tuning the fail safe with/around cleanflight? to get the idea, heres what im thinking of: since both fail safe variants have theyr disadvantages, it might optimize the whole situation if the procedures would vary depending on exterior parameters ie...

Help! I'm using cleanflight with my naze32 acro on a V2 Versacopter and cannot get cleanflight to recognize my Spektrum serial receiver (DSMX quad race type). I have read all the blogs including CLI commands and feel like I have exhausted those techniques. Any ideas? I've got port 2 set to...

So I've been having this issue with my newly bought emax nighthawk pro 280. For whatever reason, when in mid flight the quad will jolt in terms of roll or pitch, and sometimes throttle, almost as if I've applied a very small but sudden action on the transmitter itself. But I could be simply...

I've recently done a software update on my Naze32 rev 6 and the motors have become out of sync and are spinning up at different speeds however, when inside cleanflight the motors are in sync. I followed all the steps in josh's video and still they are messed up. I am currently using: flite...

Hey guys, I recently built my second quad, a QAV 210. I've been trying to tune it and it flies really well actually until I roll or flip it. As soon as I try to do one or the other, it just drops out of the sky. Just wondering if anyone may have any suggestions to fix this problem? I'm using...

I have a Mac running El Capitan (OSX 10.11) and while I can open up Cleanflight, I cannot get it recognizing the USB port. Here's what I've done: 1. Installed Cleanflight 2. Installed the CP210x USB to UART Bridge VCP Drivers 3. Open Cleanflight From here, there's no option for USB. I've...

I'm in the process of building a Y6 hexacopter following Eric Monroe's video. Parts were purchased from Flitetest. I'm using a Naze 32 rev 6 board. Transmitter is a Spektrum DX6i and AR610 receiver. I'm at the point where I'm configuring the rig following Josh Bixler's video for the Naze 32 rev...

I'm building a new quad based on the White sheep frame. It's the first time I'm messing with LEDS and not everything goes according to plan :( LEDs are more/less working : they light up, but the colors are all messed up. IMHO, it's definitely a serial sync issue but I don't understand why. My...

I cant get my V2 R620 to work with my DX6i. It will bind but on cleanflight receiver tab it does nothing. Using naze 32 with rx serial made and sbus serial recevier provider and the rx one uart2 on receiver is Sbus What should I do?:mad:

Naze32 rev6 Cleanflight Channel Jitter Hey FT. I recently got the parts for my first multirotor build (Dragonfly) with a Naze32 FC. Missing the servo, I decided to connect the FC, an ESC and receiver up to my PC to do some initial setup (binding the receiver etc.) I then noticed after having...