cleanflight

So I recently started buidling my first quad, and have done everything mechanical except attach my receiver. My problem is that my motors do not show any activity, and that I can't flash my Flight Controller. I don't know if the first problem is the result of the second, but I am stumped. I have...

So this is my first post to this forum & I am providing my first answer to this forum: This is my first quad configuration (for a Vortex 150) & have watched numerous videos & read the docs for it. I'm using CleanFlight for the configuration: I'm able to connect, I've defined switches for...

My intial question: How do i get my motors to react to my stick movements?:confused: This may be a long shot but i was wondering if someone could help me trouble shoot this last problem i have before i can get my brushed micro in the air. I am using Flysksy FS-i6 with a flysky receiver, they...

Let me start by saying I'm really ignorant about what I'm trying to do here. I've flown toy drones and my XK380 (which is still kind of a toy drone), and I wanted to go a step deeper so I bought a KingKong 100 and a Jumper T8SG transmitter to fly it with. Probably a mistake. I'm trying to get...

Hi guys ! I'm new to FPV and bought a RTF Kit from Eachine 1 month ago. Now that I know how to properly fly with it I wanted to flash it with Cleanflight just to modify PIDs/Rate/etc. So I Naze32 FC from Cleanflight and everything went well. I've setup transmitter settings so Cleanflight...

Hey everyone, I've been flying a quad with a Naze32 Rev6 line of sight for the past few weeks, and recently I just installed all the equipment to start FPV flying (camera, vtx, antenna, and micro minimOSD). However, when I went to change some settings on my Naze, Cleanflight wouldn't let me...

I recently got out my Mini Tricopter from RC Explorer to get that working again. I am using Cleanflight for setup on a Naze32. After installing the new firmware (Triflight 0.7) I went through the steps which I had done several times before. This time when I got to plugging in the battery I...

I'm a bit of a newbie and i'm having some issues with my taranis i recently picked up. It works perfectly in simulators, its bound correctly to a frsky xm+(atleast the steady green light is showing), but rates are not shown in cleanflight. In cleanflight i've set Reciver to serial-based reciver...

Hey Folks! Okay I have been building this FPV Racer - https://www.youtube.com/watch?v=Avp8MurmeEY&t I have it built but have a potential issue. When O go into Cleanflight > Motors everything spins perfectly. However, when I just plug in a battery and test it with the transmitter, 1-2 of the...

I have a Naze32 lying around from a quad build, and I built an ft flyer, Cleanflight seems to want me to have ailerons, but I obviously dont, Help?

Hay ladies and gents!!!! I'm new to the hobby, and decided to grab a TX, goggles, and start my first build. (post tiny whoop, I started there) I built the Q100 kit, no issues. Get it bound to my DX6 and hooked everything up in clean flight. Everything seems perfect, my DX6 is showing the right...

Hello guys, I just bought my first quadcopter, an Eachine Falcon 180 RTF with Naze32 FC from Banggood, and I have a problem. I mounted on the props correctly and the motors are spinning but it won't lift off the ground. I tried everything but nothing seems to fix this problem and now I don't...

Hello I'm sorry to have to post two questions in as many days but I'm very stumped. I have a NAZE32 that yesterday would automatically connect to cleanflight where I updated to the newest firmware and reconnected multiple times. Then I came back this morning and cannot get it to connect for...

I am having some issues with getting my Tx inputs to be viewable in CleanFlight. I have followed a lot of tutorials with no success. Here are my steps: 1. updated all firmware 2. changed to ppm in cleanflight and Tx/Rx 3. used the Tx inputs and with no avail The Tx and Rx are bound, I have...

Good Friday everyone! I bought myself a FliteTest PowerPack E about a year and a half ago (when they still sold the CW/CCW threaded motors) for my ZMR250 and now I'm freshening my build up and want to make sure the latest BLHeli is installed, everything is calibrated right, Oneshot, etc... The...

Hey all! Transmitter: DX6e Receiver: Spektrum AR610 6CH sport receiver Dsmx flightchip: Naze 32 ESC: Arris 20A, 2-4s LiPo PROBLEM: The controls do not show on clean flight. (No Stick movement) The controls do not work when I am connected to cleanflight and when I am disconnected. Cannot set...

Hey guys!! I'm a noob but have somehow managed to build a quad and I am now at the point of configuring my FC. I have a Naze32Thin and have a flysky fs i6 transmitter and the fs ia6b receiver. They have bound together fine but in cleanflight when I wished to select the PPM mode I receiver mode...

Hey there, I have been building a 250 class quadcopter since the last 2 weeks. I'm using the following components: 1. ZMR 250 C.F frame(Chinese clone) 2. Naze32 10 DOF Rev6 3. Marspower MX1806-2280kv motors 4. Emax Blheli (yinyanmodel.com) 12a esc's from...

I just finished building a QAV250 with a Naze32 rev6 with Cleanflight and a Taranis X9D Plus with a X4R RX. I have everything wired together correctly, as I can receive telemetry and see the control inputs in the configurator sometimes. The problem is that, when I have telemetry and softserial...

So, I am not sure where to start. I would like to use the Cleanflight passthrough to flash my ESC's. These are the EMAX-BLHeli-12A ESC's that my wife purchased with the original Versacopter suggested power pack E - good with the 2204 motors. I have the Naze rev 6 board and the latest version...