help

Hi, Been building FT foam fixed wing craft for a year or two now and ran into a problem recently with one of my pietenpols. I found an FT video A few months ago on how to setup the MZ to hover your fixed wing and went through the steps to try it out and now I can’t find the video and...

Hey everyone! FPV has always been interesting but also intimidating to me so I never took my first steps into it. That will change with your help! I really don’t understand much about FPV but I watched this Flite Test video, and said I have a Cub, I can do that! But frankly I don’t know...

So I have Smartpropoplus installed and it's sort of seeing input from the DXE when have it plugged into my computer and so is Freerider but Freerider sees the right joystick as the left and vice-versa. I'm just wondering if this cable...

Hello Everyone! I am returning the world of RC airplanes (I was very into it but have fallen out the past couple of years), and I was wondering if I was able to bind a quadcopter's FrSky D8 - SPI BUS receiver to a Spektrum DX7s transmitter. Thanks for any input (Go easy on me I am new to the...

Hi folks! If I missed the obvious location for help requests, please point me in the right direction. I am having difficulty with my first twin engine plane. I have successfully flown the Explorer, Bushwhacker, and Versa. I am getting the Sea Duck ready and having difficulty with the throttle...

I got the tiny trainer speed build kit last week. I got everything from the FT starter bundle (So I'm using the Power Pack A, a Tattu 2 cell battery, and the Spektrum DXe Transmitter). Every time I move the throttle a little the ESC beeps at me and the motor jitters a bit. I believe that I...

Hey I bought an old futaba PCM 1024z, and i dont know how to link it to the receiver, can you guys help with that.

I am building a plane for the first time and all of my electronics work properly. I have two esc's each with their own 11.7v battery (2200mAh) which are each connected to one motor like usual. I then have the two JR plugs which go into a Y-harness and go into my one single throttle channel port...

Does anyone know an easy and cheap way to make plans?

When i paint my fiber-glass fuse, the paint and primer starts to bubble up. Any idea why. I used normale water based spackle. And epoxy resin

Hi all! I’ve recently purchased a newbee drone which requires D8 mode. I’ve watched many videos on flashing new firmware on to the radio, which hasn’t been successful in terms of reactivating D8 mode. Apparently it’s been turned off and by not checking the eu box before flashing allows you to...

How to get such a high quality finish? Starting with Plain white styrofoam that the kit came in and ending with the below effect.

Would be interested to hear what your full electronic setup would be for the below. Taking it as it comes adding everything required to get RTF. i.e; Motor, battery, ESC, Prop etc. Working off this: Here Thanks!

Would it be possible to link this system up to be the control for a fixed wing UAV...? This or This

I am looking to get this fixed wing for our school cadet force. They will be learning on simpler systems but we'd love to get one of the below. Could anyone help with directing us to everything we'd need to get this flying with the end aim of using it as a sort of surveillance drone. We're in...

I am looking to get this fixed wing for our school cadet force. They will be learning on simpler systems but we'd love to get one of the below. Could anyone help with directing us to everything we'd need to get this flying with the end aim of using it as a sort of surveillance drone. We're in...

Hallo! Im building a plane for a school project and i dont want to spend to much money. So i have all the parts i need but i dont know if the battery's a have ad home are good enough. They are NIKKO Ni-Cd battery packs they are 9,6v 650mAh (i have 2 of them) can someone help me

So, I have some scraps from a small toy plane. it runs only on 2 motors, and still functions. i ripped out the electronics, and i want to build a canard-style. I also have 2 quadcopters with 6 functioning motors. could i convert these to servos and make a normal plane that runs on the drone...

I have been flying a inductrix FPV for quite a while and I recently decided to upgrade to Tiny Whoop special sauce motors and a 255 mah mylipo with the jst 2.0 connector and it worked fine for one flight but then I took it to flite fest. When I tried to take off for a Tiny whoop race it flew...

Currently I Am Working on Plans and a list of items and plans for my 1/19 scale Boeing 757-200 With United airlines Battleship Livery. I Notice on smaller rc airplane models there are clear windows on them. I Was thinking about add some to my Airplane, To save me From finding out were to line up...