kk2

Hey Everyone, I need some help on this. I just maidened my new rotor bones spider quad and everything went well. The next day I flew again and the quad pitched forward several times and gained so much forward momentum that it slammed into my shed. I am flying with a KK2.1.5 control board with...

my X style quad copter starts spinning clockwise as soon as it is in the air Orange transmitter and receiver KK2.1 flite controller Qbrain speed controller 4x turnigy 1000kv brushless motor carbon glass frame

I hope someone has some help for this. I am a newbie to RC, have electronics training and have built custom computers so have some background experience that should be helpful. My problem is with a tricopter. I am using a kk2 board with 1.6. I am sure I have everything hooked up properly and...

https://www.youtube.com/watch?v=3TYpXm5DpNU&feature=youtu.be I built this quad about a month ago and I have not been able to fly it. The problem seems to be with motor number one. When I try to take off, the quad moves forward rapidly and uncontrollably instead of staying level. I have done...

Hello, I am unsuccessfully trying to assign the SL to a switch on the Taranis . I am using the CH5 and the SF stick , all look good , but the KK2 still shows SL off. Thoughts ? Thanks, David

I have a strange issue that just cropped up. I have a 450 quad with a kk2.0 board with 1350KV motors that was completely rock solid stable, one of the motors M3 started with bearing issues so I swapped out all the motors with some 900KV motors because I didn't have a replacement 1350KV. I went...

Hey guys, so I've asked around and got a few different answers, but can you plug four 15 amp multistar ESC's (switching BEC's) straight into the KK2.1.5 (HC)? Or do you need some 'remove red wire' disabling shenanigans? Cheers.

Hey everyone I posted in the forums only once before to help give advise on a DIY quad build. Everyone was so helpful that I was able to finish building my H quad. However I'm having some troubles. The quad flies but there is a HUGE trim issue. When I do a receiver test on the KK2 board there...

Please help, I finally got all the parts but im a bit confused how to connect everything ! I connected the RX to KK2 (the new on with remote display ) CH1 A CH2 E CH3 T CH4 R CH5 Aux Rx is bound to the Taranis and i have the green light on the RX Now, when I finally armed the KK2...

I'm new to quadcopters and purchased a kk2.1.5 board to use on it. I can get it to fly alright and hover pretty well using the self leveling. However, when I try to fly forward quickly it always drifts to the left a fair amount. Is there some tuning I can do to fix this? When I fly forward...

I am building my first quadcopter using the knuckle kit I ordered from flitetest. Here are the parts I'm using: 4 turnigy multistar 30A ESC's 4 1300kv Blue Wonder Motors 1 2200mah 20C battery 1 kk2.1.5 board When I power up the motors, they all start to spin. However, eventually, motor 1...

I built a anycopter, tricpter, with kk2 V1.2 when I use the ruder it loses alt of it altitude! I guess I have to change the parameter on mixing chanels but I´m not confident where to fix it.

SOLD Sold, thanks to all

Morning Guys Today I'm here for some help with my first build. It's a tricopter with kk2.1, 750kv motors from David's build on a anycopter frame, wooden booms same as David's length and thickness , with 2 30amp Simonk esc and one multistar 30amp esc, a metal gear turnigy servo, and a traxxas...

ok so i reciently built a tricopter and planed to use this low voltage alarm but to my dissapointment i found no way of hooking it up due to buying the y harness and i was wondering if any of you know how i could hook it up either through the y harness or through the charging lead or any other...

Hello all! My first post on Flitetest forums! I just got into flying multirotors and decided to start with a tricopter. (And I'm starting to realize that starting with a tricopter may not have been the best of ideas..) I've managed to scour the web and various RC forums to be able to get my...

Hey all, I'm having an issue with my newly assembled batbone tri. I'm using a KK2.0 board. When doing some throttle ups with the entire system powered up, I'm having an odd issue. Whichever motor is plugged into the M1 slot (This is normally the front left motor) will continue to rev up to a...

Hi everyone, I finely finished my tri build and have it flying reasonably well. My problem now is the low battery alarm is not working. I have it set * 138 but even when the KK2's (V 1.6 downloaded from HK web site) readout is down to 11 volts it does not beep. The speaker works OK when tested...

I have Turnigy Multistar esc's. 2-30amp ones and 1-15amp one. a kk2 board. batbone frame I kept flipping on what I wanted to be my maiden flight. I can't even get it to hover. I Hexa checked that props and motor rotation were correct. I thought I calibrated the esc's because i heard the beeping...

Hi I built a tri-copter the same as David's (rcexplorer.se) and managed to get 3 good flights out of it. The 4th flight was the last time I saw it. Basically I lost orientation and and it just got further away and it dropped into a farmers field and despite searching several times its gone...