multiwii

Hi all, I'm trying to implement control of my quad through an XBEE. I started on this thread, which got me into the Multiwii Serial Protocol. Another thread on the MultiWii forum goes into interfacing the board through Arduino, and this library was brought up, which should execute datalogging...

Hi all, I'm very new to Quadcopters (RC in general), and I recently bought an electrohub frame along with its respective ready to fly quads electrohub electronics kit. I'm flying on a 3000 mah 4S nanotech battery. I'm not entirely sure if it's just me, because I have nothing to compare my drone...

Hi, One of those "simple" addons... I am flying a quad with a witespy multiwii pro 3 FC board on it and the oem sketch which includes the GPS. So far I love it. Decided to add a redbear bluetooth module and it doesn't want to tell me what the FC board is doing. It seems like a comm problem...

I've checked the prop direction, Calibrated the ESC's, even set the trim to the opposite direction. Nothing seems to help :( . I'm using the Flite Test Electrohub build kit, using a standard X-configuration. I think its something wrong with the programming maybe but I'm unsure. I'm using a...

Yesterday I was flying at the field and after filming I decided to use my 2200mAh packs for some leisurely cruising because lately my miniquad has been stressing me out. It was really relaxing and for some time I forgot that I was sitting next to my car, rather than floating around in the field...

Hello! I am trying to set up my Mini MWC Flight Control Board (from HobbyKing). I use the firmware Multiwii 2.4 from site https://code.google.com/p/multiwii/. When I plug the battery, only one motor rotates - that one that is connected to the port D3. How can I make all motors rotate? Could...

Hi everyone....I am new to forums i already new about FT but didn't spend any time here. i have a question for very smart people out there.As you know Dji Inspire i have a fancy ballscrew landing flapping kind of thingy for landing and its known that it bad to place FCB away from cg but it...

Hi! I'm a multiwii-beginner and I am assembling a "2.0" version of my tricopter. Last year I used a FyeTech FY-901 FC, but I wanted something with more options so I bought a Crius AIO Pro 2.0 card. I have hooked up all the electronics, and it seems to be working fine. All except the yaw servo...

Hello guys, I am trying to build up the electrohub quadcopter from flitetest using electronic kit from ready to fly quads but I have some problems powering up the flip1.5. Basically, I am at the point where all my ESCs are connected to the distribution board. I plugged the 4 of them into the...

Hey guys. I just built my second electrohub (one for my brother). After trying to maiden it and having it inexplicably flip over every time we powered up (turned out to be a gyro calibration issue as wiring, motor direction, props etc were all correct). After getting that sorted I went into...

Yo forum! I got a multiwii flip 1.5 back in May. Do not like it that much. I eventually converted my tri to a quad. I got it flying for a little while. One time I tested it, and the thing kept pitching backwards. Could not figure out why after all of the settings I did to it. During that...

Hello all, I'm kind of new to the forums, made an account and then got out of the hobby, now I'm back in it and I'm starting to consider my next build. I am a very proficient flyer and very tech savvy. I am curious about what your favorite controller board is and why exactly? I want one that can...

So I've finished building my first quadcopter following the Electrohub tutorial and hooked up a Turnigy 9x receiver. It appears to bind to the transmitter successfully, but when I turn it on normally and give it some throttle, nothing happens. The lights on the MultiWii board turn off as soon as...

Hello I am having trouble getting the GPS to work with this board. Every time I try to connect from the multiwii configuration software it cannot read the com port. However it connects fine without the GPS plugged into the ic2 board. :confused: The red light on the ic2 board is pulsing 3x...

! ! ! SOLVED ! ! ! Hi. I have been trying to set up the MINI MWC flight controller and is starting to loose my hair... Everthing seems just fine, motors beeps and all inputs can be read via the MultiWiiConf-tool But two things will now work. 1. OLED will not turn on. 2. It will not ARM...

Hi everyone So i've just build my first quad following the Flitetest H-quad plans. The only difference is that i'm using the Multiwii pro with GPS board for control. My problem is that i can't get the board to recognize anything from my transmitter. I know the transmitter/receiver works fine...

I've been hearing more and more about the Flip 1.5 from Ready To Fly Quads recently. A $15 flight controller sounds great, so I went to the website and saw more than just the Flip 1.5. There's the Flip 2.0, 2.5, Pro, 32, 32+, and Ez. Can anyone help sort all this out? :confused: BTW, does...

Hey everyone. I just got the Flip 1.5 board from RTF quads. I got it for my tricopter rotorbones and ordered it flashed for a tricopter. I have it hooked up, the motors work; but the tail servo does not move when I give rudder. When I initially turn on the tricopter, the tail servo moves...

Hi all. I like to building multirotors and I change my crafts few times per year. 2 months ago I decided to build V-Tail based on FT batBone frame and I wanted to share my experiences with you. First of all. Final craft looks like this. I followed the David's tutorial but my v-tail does not...

Hey guys so this is my first build and I am basing it on Davids tricopter build. I got a Multiwii from hobby king and I am confused on how to make it so it knows it's a tri not a quad. I have the Multiwii GUI but I seems I need something else because there are no options in the software to...