receiver

Hey guys, I'm currently having a problem with my receiver. I have the iflight Evouge F5D Digital with a TBS Nano RX. (Crossfire) My radio is the TBS Tango 2 pro. The connection was no problem and all the AUX channels also work, but I have no sticks inputs. I feel like I've tried everything...

Hi! I'm buying a used Flysky i6x with an FS-iA6B receiver. I need to test every channel, but I only have one servo, two 18650 li-ion batteries with a holder (7.3V), and a 5V power bank with two wires coming out of it. I don't have an ESC or any fancy connectors (other than female-female...

Hi all, I’m building out the simple cub with the flitetest radial b pack. I’ve been having a crazy time with getting the motor to operate. My lemon rx receiver is bound to my spectrum dxs. When I plug in my servos they all operate when given the proper inputs. But nothing when I input throttle...

I just received the OrangeRX R410X receiver and tried to bind it to my DX6. When I plugged in a battery(lipo 2 cell), the receiver got hot in my hands. I unplugged it before anything else could happen, so thankfully the light still comes on whenever I plug it in (I tried again with a life 2...

I recently got the Aura board from Flitetest and tried to set it up with a satellite receiver (WILLOWLUCKY Receiver Satellite for JR Spektrum Transmitter RC SPM9645 AR6210 6CH 2.4GHz DSMX DSM2 Satellite). When I plugged everything in, the Aura started searching for a receiver, following the LED...

I just bought a Eachine Tyro 89 and I already have a Spektrum Dxe. I'm looking for a cheaper (~15-20$) rx that'll work with both...

Hi there. The AS3X and SAFE on my AR637T receiver has the elevator correcting backwards. All other channels are correcting correctly and I have triple checked the orientation. Also the servos are all set correctly and when I pull back on the stick the elevator hues up. But when I angle the plane...

Hi there! I recently decided to give trying a fly due to the quarantine and purchased the Horizon Sport Cub S 2. I’ve been having a blast flying it so decided to try scratch building an FT P40. The Sport Cub came with a Spectrum MLP6DSM transmitter and I purchased a Spektrum AR637T receiver...

I've really been wanting to put the aura 5 in a mighty mini size Sopwith Pup I made but the satellite receiver i have ( the Spektrum SPM9645) wont enter bind mode or do anything as far as I can tell. All that happens is the small orange led on it will flash very quickly as the battery is plug in...

Hi, I have a TGY i4x (can be found here) and I would like to add a couple of switches to it so that I can drop bombs from my plane. I'm fairly new to RC aircraft and stuff but I was wondering if its possible to add a 2 position switch that takes a servo from its neutral position to fully rotated...

Hello, I have a spektrum DX6 radio. I am doing a drone, my flight controller is 9g 30.5x30.5mm Omnibus F4 Flight Controller AIO OSD 5V BEC Current Sensor For RC. And I don’t understand how to connect my receiver on it. I may not have the great receiver. Please, someone can help me to found the...

Just out of curiosity,what do the 2 switches do on my receiver in the Apprentice S?

Hello, I'm selling Fatshark HDO's with Furious TrueD diversity receiver. Googles are just like brand new, I have flown 2 times with them in 2019 summer. Selling because don't have time to fly anymore. :( I'm asking for 350 eur (googles+ receiver) . Located in Riga, Latvia. Buyer pays shipping.

I just came back from FlightFest and I am new to building air planes. I am looking to figure out how to install a FrSky Rx4r receiver for my sons commuter airplane. I bought the power pack and have a new Taranis x9 lite. The servos and engine are installed and ready to be connected to receiver.

Hi there! I'm new to this and have never posted on any forums before so... have mercy! I've never flown or built an fpv quad or any rc things before. I'm dying to do it though! And determined to do so. I'm building an fpv race quad, for the first time, following this guide: I'm using the...

hi everyone. ı try to bim my xm+ receiver with my taranis but receiver always has solid red and green lihgts so ı try to flash my receiver but ı always get module not responding error . how can ı fix this problem. ı tried all firmwares for xm+ like lbt or fcc but it didint work. please help me

I am looking for working UMX electronics including receivers, servos, and motors. Loose, or still in a plane. Brushless and brushed motors. I'm in Southern California. Flexible with shipping.

We're excited to be carrying the Turnigy 5 X Mini Transmitter& Receiver! The mini Turnigy 5X is a full range, entry level 2.4GHz transmitter that includes switchable mode functions between mode-1 and mode-2*, fixed wing and delta mix function, servo reverse, dual rates and adjustable stick...

Our servo line just keeps growing and growing and growing with excellent performers! Introducing four new 25 tooth servos from Hitec! HS-318 HSR-2648CR HS-488 HS-788

Stock up on all your favorites during our largest sale of the season now through April 12th & enjoy FREE Standard Shipping! 20% OFF Hitec Servos 30% OFF Futaba Servos 75% OFF Futaba Style Wiring & Extensions 30% - 60% OFF Actobotics 40% - 63% OFF Motor Blowout and more! https://www.servocity.com