Hey folks,
I recently started reactivating a quad build that I had laying around for 2+ years (thought I mention that so that people don't get confused with the pretty outdated hardware) and didn't touch since. Back when I left it one of the ESCs was broken, so when I picked it up again I...
All in one control board with reciever, esc and 2x servos (for tiny builds).
Okay so I know these are a thing. They are in everything from small warbirds to medium sized models. I have looked but I just can't find one online though. Anyone have any ideas on where to get them so I don't have to...
Hi,
thats my first post and also my first scratch build so I'm pretty much a newbie.
I built a FT Mini F-22 and it was working great. For different reasons I now wanted to use another ESC and I bought a cheap 30A Simonk ESC from ebay. The problem is that with this ESC I have alot less thrust. My...
These are used, tested, sets of Power pack A motor/esc. what you see is what will be included. I have 6 sets available.
Each set will include 1 motor (MT1806), 1 esc (12a), and 4 props that coordinate with the direction of the motor. Addl props sets (2cw,2ccw) available as well.
Please...
I had a crash earlier this year and had not tested things since it was cold (I only have one set motor + esc), I am not sure if this is a motor or esc problem.
Everything was working well but testing today in a new plane, I connect everything as usual, the rx gets power and servos work fine but...
I just received my new Cessna 150 and put it together, I plugged it in to test it to discover the esc does not act right. It has an E-flite 60 amp Pro Switch Mode BEC Brushless esc (V2), model # EFLA1060B. When I tried to throttle up, the motor started fine but then immediately started to slow...
Hello Everyone,
Humor my electronics ignorance, but I have been wondering about this for a while now. I've read (and heard) that 'Volts hurt, Amps kill.' If you have a low enough amperage, you can have volts to arcing all over the place without any real danger. I've read that anything above 100...
Hi, just want to share an issue I'm having, hope somebody knows how to solve it.
I was just calibrating my ESCs throttle to get them in sync on a quad powered by a KK2, but instead of the two beeps at full throttle and then one beep at idle, after the usual ''1+4 button, power up, wait for...
I'm trying to calibrate the 12A Emax BLHeli ESC that came with my FT Tiny Trainer. My receiver is a Turnigy TGY-iA6C and it is successfully bound to my Evolution. For some unknown reason I can't get my ESCs to go into programming mode. When I connect the battery, the Evolution recognizes the RX...
I have been able to fund myself for most ever other part ft sidewinder frame, motors, battery, camera, transmitter Etc. Etc. to include the original hglrc f428 fc however the pd/esc board I received does not work. So I am looking for either another f428 pd esc board or another setup to fit the...
I have been able to fund myself for most ever other part ft sidewinder frame, motors, battery, camera, transmitter Etc. Etc. to include the original hglrc f428 fc however the pd/etc board I received does not work. So I am looking for either another f428 pd esc board or another setup to fit the...
Hello guys!
Before i relate my problem i want to say that i have been researching for my problem for one week, have been testing and still cant fix it.
So, i have build my first Quadcopter a 360class 8 inch props (i have a whoop also) and i ordered 5 DYS 2212 motors and 5 Multistar 20 A ESC...
First post. Seriously need some help. I have scoured everywhere and cannot find a solution.
I have a Naze32 rev6 FCB, HobbyKing Skywalker 40A ESC's, 2212 Motors, and a FlySky FS-T6 TX and RX.
When I get power to my vehicle either through the USB port on the board, or the main power plug. The...
My brother picked up parts from an engineering class at UCI. 2300KV cobra motors, props, and a naza lite flight controller. Apparently, the naza lite is powered by the PMU, so I was wondering if I get 30 amp simonk esc with BEC, can it power the FC or are all the positive wires that go in the FC...
I have just finished completed my gremlin and all the setups. However, when it is connected to my transmitter the light on the board is blinking. Then, when it is armed it blinks twice quickly then pauses and repeats and will not arm.
When it was configured the only issue I had was the BLHeli...
So, I have some old cheap makefire* 20A ESCs, all I can afford right now being between jobs. I got some replacement motors from HK due to issues with some others. Now I have one ESC that continues to spin the motor even after disarm.
This is what I think is causing my video to be terrible. I...
Hello Flite Test :black_eyed:,
I am new to the RC hobby. I have just completed assembly of my first quadcopter. Below are the specs.
Specs:
Frame - Armattan Chameleon
FC - Matek F405-CTR (Betaflight 3.2.4 also tried 3.2.1)
ESC - 4X DYS XSD 30a v2 3-5s esc blheli_s (Unknown firmware version...
Hey all!
My name is Connor and I am a high school student. We are starting a drone racing team to compete with other schools in our district. Unfortunately, the only multirotor I have (that isn't scrapped, more on that later) to practice with is a Dromida toy that runs FPV off of WiFi. (Not...