gremlin

Hi All: I did do a search through the forum but couldn't find a tread on this topic so I apologize if this has been covered before. If it has please just provide a link to the right thread. But I was wondering if all you gremlin wizards have tried a configuration with the run cam split...

So i recently bought and built my gremlin, but haven't flown it until now because of the cold. Upon first flight, after giving it the smallest amount of throttle, the quad sporadically twitched and yawed. So, i went back and hooked it up to betaflight, took off the props, and went to the...

I have just finished completed my gremlin and all the setups. However, when it is connected to my transmitter the light on the board is blinking. Then, when it is armed it blinks twice quickly then pauses and repeats and will not arm. When it was configured the only issue I had was the BLHeli...

So I'm pretty new to this hobby. I have built and flown one plane and I want to move into the world of quads too. I am planning on buying a Gremlin kit and building it myself but I have hit a small snag. My radio is a Flysky i-6x. This radio is equipped with PPM or i-bus protocols. The flight...

I'm having an issue where my Gremlin behaves erratically and is impossible to fly. It pitches an banks without any input from the controller. It does this even when sitting on a flat table. This behavior can be seen in Betaflight as well. As I throttle up while connected to the computer...

I'm building an FT gremlin and I have almost everything working... almost. in TJ video, he clicks the port tab on the bottom left, then selects his computer port. After that, he clicks connect and it finds all his ESC's but whenever I click connect it opens a tab and says to please connect ESC...

can somebody help me? I decided for my first quad build was to build an FT gremlin but when I tried to flash the board, the computer wouldn't read it. Without the two pads being shorted the board works fine but if its shorted, the light comes on but the computer doesn't read it. anybody know how...

Hey guys, I'm having some severe issues with my freshly built gremlin. I did everything that TJ did in the video and in BF it all checks out. But after I disconnect from the computer and plug the battery in and connect to my transmitter and actually arm it the whole thing starts to wobble...

I'm having an issue with my Gremlin. I can't tell if it's the FC or the Receiver. Would someone who has a working Gremlin with a FRSKY R-XSR/QX7 combination please post their CLI dump from Beta Flight? I’ve got a couple of more things to try but I need a microSD card to flash the receiver first...

So I recently got a gremlin that was built by FT; I took it out of the box and plugged the battery in. The battery is fully charged and is a lumenier 2 cell, 400 mAh, and 7.4 volt. I was able to get my Spektrum DXe to bind to the receiver, the receiver held a solid orange light. The problem is...

For some reason I can't flash anything on to my board. So after trying many times I went on with the build. Later when programming my quad my receiver map would not display my transmitter movement. I am using a DX6e and the same receiver in the vid. I have the correct channel map and the...

This is my first post (if I put it in the wrong spot, my apologies) I received the gremlin kit for Christmas, ive built multi rotors before and even helped a friend build his gremlin) to start off im using a DXE radio (the cheap one with no screen) and the spectrum DSMX FPV Racing serial...

Hey again guys, more Gremlin problems here. So I just watched the newest FT video, and noticed how much punch the gremlins they were using to race had. Now, mine has no where near that much power. I can hardly get enough altitude to quickly do a flip. Does anyone know why this might be? My...

Hi everyone! I've been having some issues with my gremlin in Beta Flight. I've followed the video build guide very closely, but when I go into the receiver tab, all of the values are at 0. I'm using the same exact receiver as the one used in the build video, and my transmitter is a DX6i...

Hi guys, Ever since I've had my Gremlin, the performance has been very disappointing. I think the problem has to do with the FC. I have replaced both the motor and ESC that has been acting up. When I arm the quad, the motor seems to struggle to spin up, but then finally gets up to speed...

If I did this right, there should be two pictures somewhere on this post. I would really like a miniquad that I could just (literally) throw into a car and fly, and that was reliable. I have access to a PCNC Milling Machine, and some common plastic used for it, i found out, is actually somewhat...

Hello benevolent Forum Members! I just got finished soldering up an FT Gremlin, but would someone please help me out with the Betaflight setup? It's being uncooperative... I'm using a Frsky XM receiver, so when I configure the receiver in Betaflight, I choose 'Serial Based Receiver' and...

First post! I want to build a FT Gremlin but want to design my own frame and get it cut but I don't have a CNC router! Does anyone know of people who do this as a hobby or professionally? I know of online services that contract out 3D prints and I'd like something similar but for cutting parts...

In the build video for the Gremlin quad there is a Spektrum receiver recommended. I would like to use an Frsky radio. Can someone recommend a receiver that is compatible with both the Frsky transmitter and the flight control board? Thanks, John

Working with a pre built gremlin (Andres frame). It arrived last week and I have been setting it up over last two days. As far as I can tell I have setup everything on my end correctly. My issue comes with how it handles in flight. While in flight, the quad twitches on the yaw axis (at least...