issue

  1. NoobMicka676

    Need help analysing motor cut issue FT Mini Guinea

    Hello everyone , I've build a Mini Guinea and it fly perfecty 4 lipo and came back home. Came back yesterday to fly it more and it fly perfect but suddenly motor cut out not sure if i was controlling the thing but the Gyro seem to have land the thing carefully even if I did the dead stick...
  2. gourabjit singha

    Help! problem with the RPM of a motor.

    Hi , I tries making a ft guinea pig. i could make the model fine but i got stuck in the electrical part. as we know t has two motors. in my case the two motors are not running in a sync. although both the motors have same kv rating but one seems to have more rpm than the other. and this...
  3. B

    Newbie needing some help CR Ender 3

    Hello, I'm looking for some help with 3D printing with my CR ender 3. I tried following the advise from a previous post but no luck. I was trying to print some simple ribbon clips as an upgrade from my ender 3 but the top clip becomes stringy. Below is the clip I tried printing and the post I...
  4. T

    Package issues

    I ordered about $700 worth of planes for a school club recently, the order showed up today but was missing two power packs and a speed build kit. The items were listed on the packing slip but were not contained in the box. I emailed FT support about the issue but from reading around the forum...
  5. W

    Help! RX won't communicate with FC

    Hello! I am fairly new to the building of multirotors, this build being my second, so maybe I am just missing some little piece that you experienced people can point out. I am attempting to build a 90mm 2s quad, however it is proving to be more difficult than anticipated! Anyway, I digress. The...
  6. M

    Gremlin Receiver Issue in Beta Flight

    Hi everyone! I've been having some issues with my gremlin in Beta Flight. I've followed the video build guide very closely, but when I go into the receiver tab, all of the values are at 0. I'm using the same exact receiver as the one used in the build video, and my transmitter is a DX6i...
  7. casedog21

    FliteFest East 2017 - Radio Issues

    I just got back from #FFE2017 and again it was a great experience. This year we had two new guys with us that hadnt been before and they had a great time as well. I noticed that there seemed to be a lot of people, including the five of us that had radio issues at some point during the event...
  8. D

    Trim Drone, roll issue?

    Hi everyone, I have problem with a drone that crashed every time ive tried to use it the last 1,5 years. This is Very disencuraging and after trying to google the solution it seems i cant figure it out so i come here searching for the collective visedom in this community. It seems to me the...
  9. D

    Q100 build - DX6 throttle issue!!!

    Hay ladies and gents!!!! I'm new to the hobby, and decided to grab a TX, goggles, and start my first build. (post tiny whoop, I started there) I built the Q100 kit, no issues. Get it bound to my DX6 and hooked everything up in clean flight. Everything seems perfect, my DX6 is showing the right...
  10. B

    Issue between Naze32 and transmitter

    Hello all, I have been watching videos of you guys on youtube and you guys got me interested in starting playing around with quads. So I watch some more videos until I decided to go ahead and buy myself a quad :) I got a wizard x220 with a naze32 in it. I also got a Flysky 6CH FS-i6 Remote...
  11. thatfpvkid

    Qav-Build Motor/yaw Glitch

    Recently, I completed a Qav-R build using EMAX RS2205 2600kv motors, Littlebee 4in1 blheli esc, and a naze32 rev6. After the build, we were able to get it in the air with one catch. In the half throttle range (around hover) it is very jumpy. It tends to sound like a motor is skipping or...
  12. R

    Out of control - need help on initial setup

    Out of control - need help on initial setup [solved] hello! im just setting up a new quad, with an F3 and frsky receiver - i could successfully bind, but for some reason im not getting the control inputs in cleanflight the receivers SBUS connection is on CH3 of the flight controller (ofc i...
  13. F

    Versacopter V2 Naze32 rev6 fliying issue

    Hi there! Greetings from Córdoba, Argentina. Its a real pleasure to join this forum. I've been playing with Flitetest free plans for over a year now and I've decided to go to my own VersaCopter. This is my very first drone. I'm having an issue when trying to level my drone. I just can't keep...
  14. D

    Problem with Emax Nighthawk Pro 280 RTF stock transmitter/receiver

    So I've been having this issue with my newly bought emax nighthawk pro 280. For whatever reason, when in mid flight the quad will jolt in terms of roll or pitch, and sometimes throttle, almost as if I've applied a very small but sudden action on the transmitter itself. But I could be simply...
  15. J

    KK2.1.5 Refusing to arm!

    I recently built up David's Tricopter v3 with a kk2.1.5 flashed with steveis's latest 1.9 s1 firmware. My transmitter is an OrangeRx t-six with a orx dsm2 receiver...
  16. J

    DJI E300 ESC issue setting up F550 w/ CC3D

    I'm setting up my F550 using a CC3D board and when I go to the motor calibration part of the set up when I plug the battery in I immediately get the "abnormal signal" beeping. Using a DX8 with the regular receiver. I haven't been able to figure out what could be causing it I also posted on the...
  17. B

    Tricopter rear servo partial unresponsive. KK2.1 board

    Hello everyone, I am new to the RC hobby and decided to start with a tricopter. So far I have run into 2 issues. 1. I bought a potentially over kill receiver (AR12020) , and the kk2.1 does not seem to be able to read anything outputs. The only thing I could think of was the it may have a too...
  18. gustyk

    X-1000 Gyro not working with Futaba t7c

    Futaba 7C with X-Gyro 1000 I did some research in the forum but couldn't find the answer. I have a X-Gyro 1000 and a Futaba 7C but I cannot make them work together. For sure, the XG works because I tested with Real Flight 6.5 Interlink controller and the channels 6&7 of the simulator are...
  19. L

    FPV tricopter motor issue

    Sorry, im not completely sure if this should go here but i have this motor issue with my tricopter that i take arial photos from and i need the tri back in good shape immedietly. So my tricopter has been flying great the last week, i had to go and adjust the gyros and it seemed unstable in the...
  20. Hamdhan

    HobbyKing Wesbite experiencing problems?

    I get this message when I click some links "The page cannot be displayed because an internal server error has occurred." Anyone else has this? I think their server got issues or they are undergoing maintenance