• This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn more.

multirotor

  1. C

    6" HYPERLITE FLOSS V2 for sale will ship

    Fully built up, needs a new 4in1 esc. Gets around 11 minute fly time having fun not just cruising on a 1300 mah 4s lipo. 7 minutes with a session attached. Close to 20 minutes with a 2200 mah 4s lipo. It's a long range machine for sure! It's flown over the mountains in Wyoming, Colorado, and...
  2. J

    Issue with New Gremlin

    So I have built up my new gremlin and it was flying fine for a couple weeks. Then I crashed really hard strait into a wall. Now the drone starts drifting really badly and I am not sure what to do. I have it soft mounted, tried recalibrating the acc. What else is there to do. It takes off fine...
  3. CONNXT248

    Been flying micro quads for a while. Ready for an upgrade.....

    Hey all. So I'm decently experienced with multirotors. I've gone through at least 4-5 micro quads in the past year zipping them through my house, and I've logged a decent amount of time on simulators. I have a 250 size carbon fiber "racing" quad that I bought a few years ago, but I was...
  4. NewLn

    Totally New to RC, lots of questions

    HI all, I am completely new to RC and the Forums and just want to get some help setting things up. I have always wanted to fly multi rotors since I first saw it on Youtube. I got myself a little LaTrax Alias from my hobby shop just to try out quads, and I loved it. After watching many Flite Test...
  5. G

    Flying through a hole in a cliff in Dorset UK - Beautiful

    One of the guys on the Herts FPV facebook group decided to go to the seaside and film this lovely sequence - enjoy - > https://www.youtube.com/watch?v=mtM9lkSEWLc
  6. J

    Flysky Torrent 110?

    I have a 250 quad currently, and ordered an Eachine Turbine (A slightly larger tiny whoop) because I liked FPV so much and wanted to fly inside. I found it slightly under powered and the frame had crap durability (its currently held together by hot glue and hope) but it was still SO fun to fly...
  7. C

    Issue with motors not spinning up

    I recently got out my Mini Tricopter from RC Explorer to get that working again. I am using Cleanflight for setup on a Naze32. After installing the new firmware (Triflight 0.7) I went through the steps which I had done several times before. This time when I got to plugging in the battery I...
  8. C

    Transmitter compatibility?

    Hello fellow hobbyists, this may sound stupid but I am new to the whole diy multirotor thing and I was wondering if the fr sky d4r-II is compatible with Flysky FS - i6S 2.4G 6CH OSD Transmitter, I know the transmitter isn't great but I got it off a friend for free so I'm not complaining. I also...
  9. DiveBombRC

    Suggestions On my website. roguedrones.biz

    http://roguedrones.biz I do work for: Real estate, action sports, cinematography and more. Check out my website at www.roguedrones.biz just getting started so contact me with questions, price is negotiable. includes short highlight edit or longer edit for different applications. let me know...
  10. L

    Still no lift off

    I started gathering parts to build a multirotor awhile ago I got a bunch of cheap parts hoping to get it to fly. Originally I was going to program an arduino to be the controller but changed my mind in hopes to get it to fly and switched to a naze32 rev5. Problem is it won't lift off, it keeps...
  11. N

    Racerstar 30a esc freak out with Kiss FC

    I have recently finished a quad build, but once I arm the quad and apply throttle the motors don't spin until i give full throttle and the escs begin to beep. There is no control over the motors and as far as I can tell everything is wired correctly. I have manually calibrated the esc using the...
  12. I

    FPV Racing Serial Receiver Help

    So I ordered the Eachine Wizard X220 ARF (Almost Ready To Fly). I have a Spektrum DXE Transmitter so I wanted a receiver that would work with it. I got the FPV Racing Serial Receiver and wanted to know if and how I could plug it into the FC (Flight Controller) or if I need to solder it. Here is...
  13. J

    KUDORONE

    lately Ive been seeing alot of ADs for this "KuDrone" a 4k Micro Quadcopter (about the size of a Nano QX) priced at about $109(us) advertised but its more towards $200. its an IndieGoGo campaign $50,000 goal but they achieved that and are currently around $120,000. im just wondering how evryone...
  14. VolksRocket

    My Octocopter Project!

    Hi, This thread will be for my latest OctoCopter Project! I think you will find it very interesting! The first discussion point is to determine if I want to build a Octo + or Octo x configuration? Let me have your thoughts!
  15. JimCR120

    Blade Torrent 110

    I just came across this in my inbox: The Blade Torrent 110 It looks like it has what I want most in a mulitrotor and lacks what many of us didn't like in the micro quad category. At $200 for the BNF FPV it looks more of a good deal than the Inductrix 200 with more options for batteries. For...
  16. F

    Motor Mounting

    Ok, so i am building a Lumenier QAV-R, the frame is 4mm thick, the motors im using come with 5mm screws. is that long enough? is 1mm enough? or should i buy longer? how much space is there before i screw into the stator? Im using the Lumenier 2206 2350kv motors Thanks everyone for the help!
  17. W

    HELP! KK2 WILL NOT ARM WITH VERSACOPTER!

    I have a versacopter with an orange receiver and a KK2.1.5 board with the remote programmer and it will not arm. ESCs are calibrated, it is bound, it lights up, does its beeps, but when on my DX6e I put the sticks on down and right to arm, it will not arm. PS. all trims are centered + good...
  18. R

    Hello people I have an interesting idea I want to do using magnus effect

    If you haven't heard of the magnus effect I suggest you go to youtube and check it out, very fascinating how it works.' My idea is to take a multirotor and have 4 spinning barrels with veins on them to catch wind and create lift hopefully letting you ease off the throttle and conserve power...
  19. R

    Ever Made an FPV Gate?

    I recently discovered a very easy and inexpensive way to build an FPV gate for multirotors, but I was wondering what other people have done to make their own. FPV gates are very expensive to buy and not always the most cost effective or easy to build, but I'm sure there are some easy and cheap...
  20. N

    Mavic Pro shipping delays

    I pre-ordered the DJI Mavic Pro towards the end of October. Unfortunately DJI has had massive shipping delays due to the unforeseen overwhelming demand for the Mavic Pro. Needless to say, I've yet to receive mine. Has anyone received their's yet? If so, about when did you order it? (I've been...