problem

Hi, so im building my first drone and it seems that everything is working, i calibrated everything including the escs, i got the drone to work motors spinning and all but when i turn it off and back on it all connects and turns on but when i push up on the throttle nothing happens, I checked if...

So I was flying it yesterday and everything was alright. I didn't crash it and got some great footage. Anyway, today I took it to a park and tried to fly it. I was surprised when it armed and everything, but the motors didn't spin. I went onto betaflight and all the settings are the same...

I have been flying a inductrix FPV for quite a while and I recently decided to upgrade to Tiny Whoop special sauce motors and a 255 mah mylipo with the jst 2.0 connector and it worked fine for one flight but then I took it to flite fest. When I tried to take off for a Tiny whoop race it flew...

I was considering buying a gremlin when I saw a review on the power pack g v2 saying that it didn't work properly on the gremlin frames. I was wondering if this is still an issue? If this is still an issue is it possible to fix it?

Hey everyone, I'm currently trying to finish up my FT-22 (my first scratch build ever) and I've encountered problems with my Power Pack B that arrived yesterday. I have the ULTRA 2812 1200kv Motor which came with the power pack, but I have no screws to mount it to the firewall with. There were...

So I bought this transmitter like 6 months ago just recently ,whenever the Walmart foam plane video came out, took it out of the box and flew 3 short less then a min. each test flights for a plane and now when I turn it on says Rx battery is dead. I only had 2 lipo's so tried the other same...

Anyone can help me? I dont know what is happening with my drone, but sometimes, in mid-flight one of my motors kinda gets stuck and the drone flips over and fall (video below). I didnt had any major crash, but i suspect it can be one of the ESCS. Also i have recently flashed Betafligt on the...

So i recently bought and built my gremlin, but haven't flown it until now because of the cold. Upon first flight, after giving it the smallest amount of throttle, the quad sporadically twitched and yawed. So, i went back and hooked it up to betaflight, took off the props, and went to the...

Hello! I am fairly new to the building of multirotors, this build being my second, so maybe I am just missing some little piece that you experienced people can point out. I am attempting to build a 90mm 2s quad, however it is proving to be more difficult than anticipated! Anyway, I digress. The...

Hi everyone i have been trying to setup my naze32 for the past week. The motors spin up fine from cleanflight but when i try to use my Transmitter it the motors go all out of sync. Here is a video of my problem. https://www.youtube.com/watch?v=eb53EyioDug this is not my video but its the same...

My spectrum Dxe transmitter is acting strange. When I turn it on, the spectrum logo light turns red instead of orange and makes a lower beeping than the normal sound when it turns on. I can fly with it but the red light and beeping sound continue, more and more frequently. Has this happened to...

Hi All, I'm a noob to quadcopters/drones and dont really know where to start when problem solving. I have a Syma X5SW-1 and have managed just one flight. The day after this success i powered it up again pushed the accelerater forward to find the propellers would spin for about a second then the...

Hi There, For the first time in my life i'm building a drone. It's going to be one for aerial photography and video. I'm almost done with it, but i ran into a problem i can't solve. I'm using a Q-brain 25amp 4-in-1 esc, in combination with a standard turnigy 9x receiver, and a naza-m lite...

Hello all, Sorry if this has been asked before, kindly point me to the right thread. I've had a Graupner MZ12 for over a year now, really happy about the radio. I use it with three planes, moving the receiver back and forth. Today when I was going to fly I couldn't get the transmitter to bind...

Hi guys ! I'm new to FPV and bought a RTF Kit from Eachine 1 month ago. Now that I know how to properly fly with it I wanted to flash it with Cleanflight just to modify PIDs/Rate/etc. So I Naze32 FC from Cleanflight and everything went well. I've setup transmitter settings so Cleanflight...

Hey everyone! I recently received a small AIO cam from Gearbest, so I could do some micro FPV with it, however when I plug it into power, I get signal for jut a couple seconds, until it just vanishes. I've uploaded a little video here to visualize the problem. I had another one of these cams...

Yesterday I finished building a hell whoop. I went out to fly it and after a 30 seconds the motors turned off. They would re arm fine and I could fly around for a bit more before the turned off again. Inspected the problem and noticed that after a while that motors are on the receiver status...

Hi everyone! This is my first post on this forum, and I wanted to ask a question regarding my Quadcopter. I'm using a 250 frame with a 3 Cell 2250mAH Lumenier battery, and it has 12 Amp BLHeli ESCs, along with EMAX MT2204 KV2300 Motors. As I have only flown this drone for roughly three months...

Hi everyone, I have problem with a drone that crashed every time ive tried to use it the last 1,5 years. This is Very disencuraging and after trying to google the solution it seems i cant figure it out so i come here searching for the collective visedom in this community. It seems to me the...

Hello everyone, I'm having trouble binding my Taranis Q X7 with an XM receiver. I followed what I thought was the proper sequence. Transmitter on, then found an open receiver space, presses [Bnd], and heard the chirps coming from the transmitter. Then I held down the bind button on the receiver...