problem

So, I recently bought an nighthawk 280 pro. Flew it a couple of times, then I decided to flash cleanflight to it (came with baseflight) To my knowledge this quad comes with a Skyline 32 board, an intergrated 12A ESC's. After my flash to cleanflight I enable Oneshot, flew it two times, had a...

Hi everyone. Ages ago I bought a orangeRX openlrs 1W module second hand. I had no idea what I was doing back then, so It got thrown into my box of parts for ages. Since then I've got good at fpv and wanting to give long range a shot. Pulled it out and tested it and it worked fine. I had no idea...

Hey FT. I've recently completed my first ever multirotor build with the Electrohub kit and Powerpack from the store. The parts are as follows: FT Electrohub frame. Emax 2213-935 kv. motors. Naze32 v6 flight controller. BL Heli 20 Amp ESC. FPV Rail - Long version DJI style landing gear. AR610...

So port four on my quad is not letting my motor to spin up. I was wondering if I could change it to port 5 on the naze32 because everything else is working. I tried to do custom motor tab but couldn't get it to switch to port 5. Thanks for the help

Hey guys, Been lurking the forums for a few days, yall have a great community. Flitetest is one of my favorite youtube channels… often catch myself watching flying toasters and insect-like rubber band planes slowly circle around the room when I should be sleeping. (I also want Josh to drop...

Hello there, This is my first quad build :o, and i'm having problems with the Emax simon k 12A esc. When i connect the esc to the battery, it does nothing but emit a starting sound, then stop and nothing else happens, even the sounds related to the configuration by transmitter, which happens...

i have had my ZMR250 racing quadcopter for a while now and the 3rd and 4th ESC outputs don't work so i have desoldered those pins and resoldered them onto the 5th and 6th places and the motors spin but i have to set it up in cleanflight asa hex to get it working, i can set it up as a quad...

Hello Flitetest Forum Members, as I am a total NOOB to scratch building, I have come across a problem in my first build(mini guinea). One of my motors starts to jitter every now and then, and then takes about a good 10 seconds to correct itself. I have checked to make sure it is not the esc, the...

So I recently put together one of my first speed-build kits from flite test, an FT Viggen. I was super excited to get it in the air using the 70mm edf setup from Grayson hobbies. When I finally got out to a field by my house to fly it, I ended up crashing and wrecking the airframe on takeoff...

Hi all, I recently borrowed my friend's F450 running on kk2. He warned me : "my quadcopter was working great until one day, the kk2 didn't recognized any pitch input." :( I said I would try to fix this : I tried EVERYTHING ! (from unplugging and plugging back the RX to a whole factory reset) ...

Help is needed! I have nearly finished my not so fancy kk2 quad and on its maiden, one of the motors stopped turning. I needed to push it a little to get it going, otherwise it would just wiggle, and I also need to move my throttle nearly halfway up to start the motors. Im using the reccomended...

i just built my first miniquad nothing special just lokked fun and i desided to try :). i am running a 35 mhz. but i am plannig on upgradeing using the frsky module. the problem for me right now is that my signal sometimes just gets random feedback. when i hooked it up to clean flight evrything...

Hello all, A couple of weeks ago I purchased the Electrohub quadcopter kit. After watching the videos, it went together very smoothly. After setting up the Naze 32 board I have come across an issue that I hope someone can help me with. I am currently using the featherweight lemon rx receiver...

Building my Simple Storch Wing tonight and I messed up. The bottom of my wing is not flat, it curves up at the last grove before the leading edge. I have built the bloody wonder, the Simple Soarer, a blunt nose Versa, and a Spit and never had an issue until tonight. Should I scrap the wing...

Hi, I am very much a beginner, and a friend and I just completed an electrohub build. It took a long time troubleshooting various things, but everything thing finally functions for the most part. However, when we take off, the quad starts to spin counter clockwise, somewhat aggressively...

Hello! I recently invested in some fpv equipment, but when I powered it all up, the monitor shows no video. Here is a video of exactly how it is set up. If anyone can find a problem, please let me know, since I have no idea why it does not work. My Setup: Mobius Action Camera readymaderc...

Hey guys, I really need someone's help on this... I've just received new Emax brushless motors from Banggood and one isn't working as it should be. Most of the time, it oscillates and doesn't spins properly. However, it works fine without the prop, but as soon as I screw the prop on and I...

Hi, first time poster here :). Small Intro (feel free to Skip): I startet RC flying after I stumbled on the Flite Test Beginner series in YouTube. I decided that I want to build from Scratch. After flying for some time the FT Flyer I built the FT Delta to learn to yank and bank. Then I had the...

I got a 'SkyTech M62' qudcopter for xmas and its fun everybody in the family played with it but this morning i woke up went to play with it and it wont take off. I put the throttel to full power and all the propellers spin fast but it wont come off the ground. I really want to fly it but this...

Hey all! Bought my first multirotor yesterday, a Blade Nano QX. I'm having a lot of fun crashing it around my living room. After about a day (and probably upwards of 100 crashes, although at 18 grams the crashes are pretty uneventful), one of my motors is making a loud buzzing/humming noise...