turnigy

I recently bought two Turnigy Plush 18a escs to replace some that I burned out on my tricopter. I put them on and noticed that they were smaller than the other one. The new ones were version 4.3, while the old one was version 3.1. I turned it on and the 3.1 started smoking and melted half the...

So I just got my new Turing 9xr Pro and was messing around with it. I screwed up a few things and couldn't figure out how to fix them, so I figured I would just reset it to factory, so looking around I came across a reset button under the flap with the micro sd card/usb/headphone jack. After...

Hi Guys, Newbie here! I made the Hovership MHQ2 racing quad, but I'm having issues controlling it. First of all, here's the complete gear that I'm using: Quad body printed using the Markforged Mark One printer Naze32 Rev6 FC Turnigy TGY-i6 transmitter and receiver Hovership H-12A ESCs...

Hi there, I had my maiden today with my first self built plane - the FT flyer. It flies great, but I noticed something I'm not used to. The Powerpod is equipped with Turnigy Park 300 motor. The motor won't start spinning before giving it about 3/4 of throttle on both 2s and 3s cells. After it...

Hi, I'm using the Turnigy TGY i6 transmitter for my quadcopter but I have a question about flight modes. I want my quadcopter to auto-level once I release the right stick, and I've read that this can be made using "Attitude" flight mode. But I only found Normal and sport flight modes. Then...

I just visited HobbyKing and there is a new firmware update for this radio http://www.hobbyking.com/hobbyking/store/__58455__Turnigy_TGY_i10_10ch_2_4GHz_Digital_Proportional_RC_System_with_Telemetry_Mode_2_.html I plugged in my radio and the PC was supposed to update drivers etc but its not...

Hi guys! I've encountered a problem, and it's getting really annoying. I have a Turnigy 9X V2 transmitter with stock modules, and er9x firmware. After several months of use the throttle stick signal started to jitter, and jump up and down. It's quite random when and where it does this, but it's...

Hi all, Wondering if I can get some help here. My Raptor is setup as follows, Turnigy Park 300, 1600 kv 18 amp turnigy esc 8x6 prop 1350 mah 3s With this setup I am pretty happy BUT..... The motor is kinda hot (hot like, I can't hold it in my hands for more than 10 seconds) when landing...

Hi All, I've got a set of pretty much new Turnigy Servoless Retracts - 140mm Oleo that I'd like to get rid off. They were installed on an X8 project which never got off the ground (excuse the pun!). I'll include the wheels for free! As new without the box, EXCEPT when I removed them from the...

Hi I am setting up a kk2.1.5 on my hex rotor. Turnigy 9x transmitter and receiver stock kk2.1.5 from hobbyking stock turnigy plush 30amp esc multistar 2213-935 motors The problem I'm having is that no matter what I do I cant get the throttle to zero in the receiver test, the lowest it goes...

Let me know if anyone else has seen this. I have a brand-new Turnigy 9XR Pro transmitter. I am new to RC so this is my first "Big boy" transmitter. I have noticed, just playing around with it before I got my module in the mail, that the rudder channel isn't at 0 when the stick is at 0...

Hi all, I'm new to quads and also the forum so firstly I'd like to say hello (Hello) :) Now that's over with time for the noob questions that will do doubt come from me in there hundreds! I've already order all the parts for my build which i shall list now so you guys have some idea what I'm...

Hello all I have been slowly building my first quad, i have been involved with RC cars of all types for many years and this is my first foray into flight, i am using the following: Naze32 propdrive 28 motors hobbyking 20A Multo rotor ESC's Turnigy UBEC Turnigy TGY-I6 RX/TX got it all set up...

Currently trying to map my controller on the openpilot GCS with the openpilot CC3D and I keep hitting a snag where It will either not register on of the sticks or the flight mode switch. I am really confused if this is a controller problem or a receiver problem. Any help would be great! And this...

I'm looking at upgrading my TGY 9x Radio for the FrSky Taranis. However having 10 models each with their own 9xV2 RX makes the upgrade much more expensive than first thought when considering changing out all the receivers. I've looked into the FlySky module with the idea of using that to bind my...

Hi folks, I have looked at a heap of posts and cannot find an answer to my problem so I appologise if it has been covered before. I have just completed my first build of the FT Electrohub with the flip 1.5. I am using a turnigy 9x controller and receiver. When I calibrated the esc's they...

So I've finished building my first quadcopter following the Electrohub tutorial and hooked up a Turnigy 9x receiver. It appears to bind to the transmitter successfully, but when I turn it on normally and give it some throttle, nothing happens. The lights on the MultiWii board turn off as soon as...

Guys, I am a newbie just getting into this hobby. I just finished building my first ever plane which is the FT Delta. So, I bought some electronics at I would need. (Which is almost everything including radios). Then this is the first problem that came to me : How do I charge my battery? I...

I haven't found any cases or solutions for this that worked for me on the Internet yet so hopefully we can solve this for anyone else that might be having this problem. I’ve been building a quadcopter and the motors do not spin at the same time when I increase the throttle. I’m using a KK...

Hi everyone, So i just made my first rc purchase, I'm waiting for a big box from hobbyking with all the bits and pieces to scratch build the Flitetest H quad (I know this is probably jumping in the deep end but sure live and learn). My question is will the turnigy 9X receiver work with the...