esc

I have recently bought a Versacopter V2 with the GR 18 and MZ 12, I got everything setup except a bit of the radio and receiver setup. I have found out a while ago that the one of the motors would just beep over and over and wouldn't spin but the other 3 did but just today I started the...

Hello everyone! I'm new to the Naze32 Board, and currently having issues with my motors. I am running an AfroFlight Rev5 board along with DYS 1806 2300kv motors, Turnigy 10A ESCs, HK6S, and a Turnigy nano-tech 1.3A 3S battery. I am able to arm and disarm the motors using the transmitter...

Hi there. Yet another noob looking for troubleshooting help! My Versacopter worked flawlessly for several months until I had a bad crash and rebuilt. Ever since the rebuild, it will only fly using my 3S battery. I have 2 other batteries which are 4S. When I try flying with a 4S battery, it...

I recently flashed betaflight 2.7.1 to my FC and now I'm running into a weird issue. The craft now rotates 90 degrees in the other axis after a flip or roll. So once I complete a roll, it will pitch down 90 degrees just after stopping the roll. It will also roll 90 degrees after completing a...

I am building a FT Guinea Pig with dual Powerpack C. I am running a XT60 Power Y-harness to both ESC's/motors. I want to use my Lumenier 2250mAh 4s 35c Lipo for a little bit more flight time and power. Will I ruin my escs or motors? I greatly appreciate any input. Thank you all!!! Eddie

FPV quads have changed my life. I started with a Versacopter 2.0 with MT2204 2300KV 12A simonK ESCs, and rebuilded my quad on a Reptile Martian 255 frame am looking for the one and done (for now) upgrade for my motors and ESCs. I drool over videos of guys like this...

Hi there, i use a kk mini and Afro 20 Amp ESCs for my tricopter. I calibrated the esc manuallly over the reveiver but the motors are not spinning when i connect them to the kk2 board. The receiver test shows that every sinal comes in wright. If i now pull the throttle up, the motors are not...

I recently bought two Turnigy Plush 18a escs to replace some that I burned out on my tricopter. I put them on and noticed that they were smaller than the other one. The new ones were version 4.3, while the old one was version 3.1. I turned it on and the 3.1 started smoking and melted half the...

Hi there, i am trying to calibrate my Esc connected to a KK2 Mini. When i am trying to do the calibrating circle i can wait for hours for the 2 beeps that should say that the calibration worked. i tried to use the starting mode to test the esc and motors, and when i pull up the throttel in...

I don't have anything to check the true current so I'm not sure what's going on. I'm wondering just from my set up if you guys can tell if I did something wrong. I built a Kraken, I'm using two Suppo 2217/7 motors with Hobbyking 30amp esc's running 10-4.5 props . I did use my multi meter just...

I just investigated a failure on my newly bought HK Spec FPV250. This is what happened: I successfully ran through my first battery, fiddled with the settings, hovered it a couple of times. All seemed great. Then I disconnected the battery and switched to the next - nothing happened. No LEDs...

Hey guys, I would normally troubleshoot this myself, but I am a little tight on time. I just flashed CF back onto my naze after running dRonin for a little bit. I had to short the boot pins to get it flashed, but it connects to CF configurator now. First I went back to CF 1.09 because I had some...

Hi. I've recently bought the Tarot ZYX-M FC due to the similarities to the DJI Naza v2, but I have a couple of questions regarding its installation. It comes with a PMU, which from I understand it converts the LiPo voltage down to 5V and 12V to power things like gimbals etc. The PMU connects...

I am working on a project that requires a brushed ESC. I'm looking for a cheap one under $10 if you are willing. Any amperage rating is fine. I can pay shipping. Colorado Springs, CO USA

I'm in the middle of my first racing quad build and having problems with my transmitter communicating with the FC. really need some help! Equipment: Emax ESC (Simon K), CC3d FC, Spektrum transmitter and receiver (AR7700). From the start I had issues getting the ESC's to go into program mode. I...

:applause:Hey All, So i'm a complete newbie to this site and the whole quadcopter hobby, it's been quite the experience so far!!. After tons of research and Youtube Videos I thought I could build my very first FPV250 quadcopter without any hassles - but of course nothing goes smoothly ;). After...

So, I recently bought an nighthawk 280 pro. Flew it a couple of times, then I decided to flash cleanflight to it (came with baseflight) To my knowledge this quad comes with a Skyline 32 board, an intergrated 12A ESC's. After my flash to cleanflight I enable Oneshot, flew it two times, had a...

I bought the Versacopter with the E pack. I assembled according to the instructions on the videos and managed to configure the Naze 32 rev 6 according to the instructions. The problem I have is that the motors don't spin as they should. When I turn on the throttle the motors just vibrate but...

I bought: 1quanum falcon quad frame 1 afro 12a esc !!! Oops! 4 multistar motors 1 orange rx 4channel with 6channel ppm and a naze32. My1st quad... I realized my mistake and went to the local hobby shop and bought 4 hitec 12a multi rotor esc WITHOUT bec. My second mistake/oversight. Short of...

Hi all, This is the second issue I am having with my scratch built H-Quad. I had two escs that had a problem where after arming they would just slowly jerkily spin. I got a replacement ESC from FT and that fixed the one that was really bad, but the other one still has it. The one that doesn't...