naze32

WARNING- !I am a NOOB! I have made a Quadcopter using DJI F450 Frame. I have 4 1000kv chinese Motors and 4 Chinese ESCs connected to a NAZE32 rev6a 10dof. Firstly all ESC got calibrated properly but after some time 1 of the ESC got dis-calibrated (Throttle starts late). Now this ESC does not...

Hey all! Transmitter: DX6e Receiver: Spektrum AR610 6CH sport receiver Dsmx flightchip: Naze 32 ESC: Arris 20A, 2-4s LiPo PROBLEM: The controls do not show on clean flight. (No Stick movement) The controls do not work when I am connected to cleanflight and when I am disconnected. Cannot set...

hey all. Here's the info. Quad: Arris 250b http://www.arrishobby.com/arris-xspeed-250b-fpv-racing-drone-unassembled-quadcopter-super-combo-w-f3-flight-controller-us-warehouse-p-3451 (I swapped out the flight chip with a Naze 32 bought from the flite test website because I accidentally fried the...

Hi guys/gals, I've just started out in this space, and I'm happy to say that 3 months later and many burnt fingers of soldering wires, I finally have a quad copter working...sort of. Here's my problem. The motors spin up when instructed through Cleanflight. I can drag the slider and the motors...

Hi guys & girls, I have recently built my first quad(250mm)- zmr250, naze32, 2280kv motors & emax blheli escs. I'm currently using Orange 1000mah 30c-3s batteries with Imax B3 compact Lipo Balance...

Hi there fellas, I've built a quad(250mm) using these parts: 1. ZMR250 clone frame 2. Naze32 10DOF Rev6 3. Emax 12a BLHeli esc 4. Marspowers mx1806-2280kv motors 5. 2000 mah 3s-30c Lipo Battery 6. Flysky FS-i6 tx with an ia6 receiver. I want to add an fpv system on the quad. But the thing is I...

I got a EMAX Nighthawk 250 kit for Christmas and a Turnigy 9x radio and receiver. I had read that the naze32 was better than the CC3D so I put a Naze 32Rev 6 on my quad. I should probably mention that this is my first miniquad build and I have zero flying experience. My problem is that I can't...

Hey there, I have been building a 250 class quadcopter since the last 2 weeks. I'm using the following components: 1. ZMR 250 C.F frame(Chinese clone) 2. Naze32 10 DOF Rev6 3. Marspower MX1806-2280kv motors 4. Emax Blheli (yinyanmodel.com) 12a esc's from...

I just finished building a QAV250 with a Naze32 rev6 with Cleanflight and a Taranis X9D Plus with a X4R RX. I have everything wired together correctly, as I can receive telemetry and see the control inputs in the configurator sometimes. The problem is that, when I have telemetry and softserial...

i have been fighting an ongoing battle with my Naze32 Rev6 and its uncanny want not to fly. i had my FT210 flying not to long ago and damaged my Video transmitter and was grounded while a new one was shipped. after putting everything back together i decided i would update to the newest Firmware...

i have two naze32 rev 6 boards, one new never flown and one that has been used before. they are both having the same problem. when you hook them up USB only everything seems fine, you can flash firmware and change pid save and reboot no problems. however when you want to calibrate the esc as...

hello all, I have 2 Naze 32 boards V6, one brand new and one with heavy use. the issue im having is when i connect the board to clean flight everything works, i can flash software i can change PID's however as soon as i connect my lipo battery everything freezes. i am unable to calibrate my esc...

Hey guys I need some help. My naze board has been stuck in failsafe and I have no clue how to fix it. In cleanflight I get a response from each of the channels under the receiver tab, which means I'm getting a signal but the naze is still in failsafe.

Hello, first time posting! As the title states I started my versacopter build over the weekend and when I went to test the motors in clean flight I get error beeps (I assume that's what they are...). Also I ordered the versa kit with the new "better" e-pack motors, maybe that's causing the...

Well, it's me again... I've got a new problem with my 230mm quad... First of all, I got it flying for like 4 minutes yesterday, which is good, it flew pretty well. When I tried it later that day again it started showing some weird behaviour: When I arm it, the motors start spinning at minimum...

Hi everyone, I'm new to this forum and sadly the first thing I have to contribute is me bugging you with a problem that I have with building my second quad (a sub 250 quad). The quad uses a Naze32 flight controller (Revision 6), 4 x 12 Amp Afro ESCs, 4 x MultiStar Elite 2300KV motors and a...

Hi The guilty truth - I got myself into this mess by doing a probably unnecessary reboot of my FCboard...I was frustrated and wanted to start over. Anyways, here's my situation: I'm using cleanflight and a naze32 REV6 By shorting the boot pads on the naze and using the "no reboot sequence"...

Hi. I have a few questions. I am planning on getting an FT Versacopter for FPV, using Power Pack D (or the one for mini quads, if I'm wrong), but I want to try to use the Naze32 board as my FC for the Versacopter. I use the KK2 board for my Electrohub quad, which has a screen to program it right...

Help! I'm using cleanflight with my naze32 acro on a V2 Versacopter and cannot get cleanflight to recognize my Spektrum serial receiver (DSMX quad race type). I have read all the blogs including CLI commands and feel like I have exhausted those techniques. Any ideas? I've got port 2 set to...

So I cannibalized the receiver out of a now scrap quad I built and I am now building a versa. however when trying to connect the naze to the ar, it does one of 2 things. 1) which is nothing, no power at all. 2) it receives power but no communication. when I'm in cleanflight, in the receiver...