naze32

Newb to the forum, but a sub to the youtube channel. Just switched from cc3d openpilot to The naze32 rev6 10dof, and cleanflight which is a nice change. Ive done some research on how to tune the pids for altitude hold, but Im looking for someone that has pids for a zmr250 that I can start from...

Hey guys, I hope someone can answer this for me. I have very recently started getting into multirotors and fell in love right away thanks to the youtube videos from Flitetest. My first quad was a 3D printed V-tail ( http://www.thingiverse.com/make:197915 ) and I soldered the ESC pins using...

hello from Vancouver BC Canada. i'm new to the forum, and also new to the RC world. i'm looking for advice on buying a transmitter/receiver/controller. i just built my Versacopter V2 and i was originally planning to buy the Graupner MZ-12 & GR-18 combo from FT, but it was out of stock at the...

I cant get my V2 R620 to work with my DX6i. It will bind but on cleanflight receiver tab it does nothing. Using naze 32 with rx serial made and sbus serial recevier provider and the rx one uart2 on receiver is Sbus What should I do?:mad:

Hey FT. I've recently completed my first ever multirotor build with the Electrohub kit and Powerpack from the store. The parts are as follows: FT Electrohub frame. Emax 2213-935 kv. motors. Naze32 v6 flight controller. BL Heli 20 Amp ESC. FPV Rail - Long version DJI style landing gear. AR610...

Hi everyone! Rich M here :) I'm having a problem with my NAZE32 on a 250 sport quad. It flies great and very stable, easily does all the things you want from an 250 FPV platform, until you cut throttle. Because it has so much lift, it's hard to get it to lose altitude, while right side up...

I bought: 1quanum falcon quad frame 1 afro 12a esc !!! Oops! 4 multistar motors 1 orange rx 4channel with 6channel ppm and a naze32. My1st quad... I realized my mistake and went to the local hobby shop and bought 4 hitec 12a multi rotor esc WITHOUT bec. My second mistake/oversight. Short of...

Naze32 rev6 Cleanflight Channel Jitter Hey FT. I recently got the parts for my first multirotor build (Dragonfly) with a Naze32 FC. Missing the servo, I decided to connect the FC, an ESC and receiver up to my PC to do some initial setup (binding the receiver etc.) I then noticed after having...

Hi everyone. I've finally gotten around to building my Versacopter and have sourced my Naz32 rev 6 board outside of flitetest. In any case, I have it all soldered up (with a sidepin layout) and it seems the new board doesn't cleanly fit into the versacopter becuase of the 10x1 pin breakout...

I've got a problem with my quadcopter. It's a 250, Power Pack E, Naze32 racing quad. I recently had to replace the FC, and once everything was back together, I plugged in the battery and tried to test it. Everything seemed to be working as normal, except that there wasn't even lift among the...

Hi all, I am not able to find the yaw reverse options for the tail servo in Cleanflight 1.1.0 configurator, has anybody had the same problem and resolved it? I feel my options are in CLI somewhere. Thanks in advance.

I've watched the FT Naze 32 board setup video (for the 10th time) and wanted to ask for assistance. I'm trying to setup my new Naze Acro board on my quadcopter. I went through all the steps in the video but cannot get my throttle, roll, pitch and yaw signals from my receiver to register with...

Hi there I just receive my new Versacopter and Naze32 board and have tons of problem with it. Firstly, Cleanflight kept giving the message "GITHUB Query Failed: API rate limit exceeded for 220.255.227.18". Secondly, when I tried to flash the firmware, it gave a message "No response from...

Hi Guys, Newbie here! I made the Hovership MHQ2 racing quad, but I'm having issues controlling it. First of all, here's the complete gear that I'm using: Quad body printed using the Markforged Mark One printer Naze32 Rev6 FC Turnigy TGY-i6 transmitter and receiver Hovership H-12A ESCs...

Hi everyone i just bought the new Versacopter, and i have the naze32 inside for the FC, but when i go to fly it it takes off and flips backwards. I have read a ton of forms saying to set up the naze32 into horizon mode instead of acro mode, but i can't find the setting to do that. I have already...

Hi everyone i just bought the new Versacopter, and i have the naze32 inside for the FC, but when i go to fly it it takes off and flips backwards. I have read a ton of forms saying to set up the naze32 into horizon mode instead of acro mode, but i can't find the setting to do that. I have...

I finally finished my ZMR250 build, but I've got a problem with it. It seemed to fly great at first until I started getting a little comfortable with it and I started getting more aggressive. I whipped it around 180 and pitched it at an aggressive angle and punched the throttle, then it tumbled...

Please can someone help me out? I am working on building my first quad (experienced pilot but not builder) and I have setup the naze32 on my custom quadcopter and pitch and roll work but I have no yaw control over the quad? The board recognizes my inputs for yaw and they are in the correct...

Originally posted in FPV, but since the problem is not specific to FPV, but the Naze32 - I figured it could go here too.. If I broke a rule, let me know and I'll delete, just trying to get help as soon as I can. I have built a BNV for FPV flight. Plan was to use a Naze32 for flight...

This is my first Naze32 so it is all new to me. This is a brand new, unsoldered board and I am using a Mac book pro. So far I have downloaded the “Silicon Labs VCP Driver install disk”, applied the “uninstaller.sh” to the terminal command window and installed the VCP driver. Restarted Mac I...