receiver

Hello everyone, this was my first time messing with FPV and I bought a Fatshark receiver and transmitter. After learning that the receiver is specifically designed to work with the Fatshark goggles, i decided to try it before putting it on the shelf. After flipping through the channels I found...

Hello All, I just ordered a test R610 V2, I electrify a lot of glow kits, I have two electrified Sig Wonders, VERY QUICK! I almost lost one last weekend due to some brownout issues on my old Orange Rx 615. I ordered the new r610 V2. I cannot find any reviews on these things. I figured...

I posted about my problem here and I still can't get the receiver working, sometimes the LED lights up for a sec or two but then it dies. Thanks to all those that helped me in the other post!

Graupner GR-24L - $55 shipped

Just got Power Pack A with a speed build kit and am trying to figure out how to attach the ESC to my receiver and get the benefit of the ESC's BEC. The BL Heli 30A has one lead for the receiver, but the TR624 receiver has a battery input and a separate channel 1 output. Anyone else have this...

Hi everyone! I am new to this forum I am relatively new to the RC hobby too. A few minutes ago, I posted the same question on a wrong forum. Anyways... I have a Flysky FS-i6 radio set with a FS-i6A receiver. After a few minutes of use, the receiver gets warm. Not hot, but warm. I am worried...

Hi everyone! I am new to this forum :) I am relatively new to the RC hobby too. I have a Flysky FS-i6 radio set with a FS-i6A receiver. After a few minutes of use, the receiver gets warm. Not hot, but warm. I am worried, is this normal? Has anyone experienced this with this receiver or any...

So I set up the versacopter exactly as they did and everything seemed to work. I had some slight problems with some lag but it was only when I'd try to pitch backwards, itd take a few seconds to register on the quad and then do it. Recently I was trying to look at all the settings and reading...

So I've been having this issue with my newly bought emax nighthawk pro 280. For whatever reason, when in mid flight the quad will jolt in terms of roll or pitch, and sometimes throttle, almost as if I've applied a very small but sudden action on the transmitter itself. But I could be simply...

Dx5e not binding to..... anything? [FIXED] Hi, Preface: I am working on a build of the Versa wing and I just got all of my electronics. Excited to try out the new receiver I got, I plugged it into a powered esc and my servos and I flicked on my transmitter, only to find that although it looks...

Hey guys I need some help with my hovercraft that I'm making. It's very similar to the one shown on Flitetest a few weeks ago. I'm trying to attach my forward thrust motor to my elevator channel. Everytime I try, it just cycles through the arming process over and over again. I tried changing...

Hi there, i got a strange issue. If i connect my kk2 mini board from pin thr,v+ and ground to channel 3 of my receiver the board goes off (or maybe just the screen - not sure). Have you got an idea what i have done wrong here? thr is connected to signal, v+ to power and gnd to ground. If i...

Hey everyone, Does anybody happen to own a Tactic TTX850? If so, how do you like it? If you don't, what do you think about it? Thanks, TheStig4449

Modifying old 72MHz to 2.4GHz with "AnyLink" adapter - or buy modern trans/receiv? I have an old Futaba Skysport 4 from years ago, complete with receiver and batteries that I used with gas models. I am ready to build my first electric (mini sportster) and came across a device that...

Naze32 rev6 Cleanflight Channel Jitter Hey FT. I recently got the parts for my first multirotor build (Dragonfly) with a Naze32 FC. Missing the servo, I decided to connect the FC, an ESC and receiver up to my PC to do some initial setup (binding the receiver etc.) I then noticed after having...

Recently my son kept stealing my Fat Shark goggles. I'd been using the Quanum DIY FPV Goggle Set with Monitor (KIT) as my GS monitor but decided I better build them up. Only one problem. With the RX from the ground station it was a very bulky over weight setup. By chance I spotted a nice...

http://www.amazon.com/gp/product/B012W6HJHG?refRID=JZT7QBWWKVPX89MX5D45&ref_=pd_ys_sa_3226142011_8 I am unsure of whether this is any good or not but would like to know if anyone knows anything

How to control a quad in the safest condition in case of fly away ? Hi, this is my first time on this forum and i'm a newbie in the quadcopter world ! First of all sorry about my English. So, I just finished (and crashed) my first quadcopter. And even if I tried, before flying, to get the...

Hey everyone, first post... So I've been meaning to ask some technical questions about the factors that are involved in the FPV system. I've just pieced together my first system over the weekend and took a maiden flight a bit earlier today, and so far it was a success, but I'm trying to...