versacopter

My first post to the FliteTest forum. Two photos of a Versacopter set up with a NAZA Lite flight control system with GPS. Powered by an 1800 mah Lipo which is mounted on the bottom of the quad along with the E-PACK 2205/2300KV configuration.

I'm new to building drones and I'm planning to build a versa copter v2 I have a spektrum dx6i (upgrading to the dx8 gen2) and don't know what receiver to put on the versa copter. I plan to also use the naze 32 rev6 on the quad. I am also curious what kind of FPV camera people recommend for...

Hello, first time posting! As the title states I started my versacopter build over the weekend and when I went to test the motors in clean flight I get error beeps (I assume that's what they are...). Also I ordered the versa kit with the new "better" e-pack motors, maybe that's causing the...

Hello, Does anyone have a way to get the Graupner MZ12 to work with a quadcopter? The version of the mz12 I have only has settings for airplane and helicopter.

Help! I'm using cleanflight with my naze32 acro on a V2 Versacopter and cannot get cleanflight to recognize my Spektrum serial receiver (DSMX quad race type). I have read all the blogs including CLI commands and feel like I have exhausted those techniques. Any ideas? I've got port 2 set to...

Just built my Versacopter. Have Graupner GR-18 receiver and MZ-12 Rx combo. Bind was successful. Calibrated ESCs ok and calibraged the Gyros also. However, when tried to fly today, normal beeps when binding happened then continuous beeps and no further response from Versacopter. Is it an...

Recently I got my hands on a FliteTest VersaCopter V2. Specs: Flite Test VersaCopter V2.0 Power Pack E (Racing Mini QuadCopter) Naze 32 Flight Controller Rev 5 FrSky XSR 2.4 Ghz ACCST Receiver The build which I will detail below was pretty straight foward and if you listen to the podcast...

So I set up the versacopter exactly as they did and everything seemed to work. I had some slight problems with some lag but it was only when I'd try to pitch backwards, itd take a few seconds to register on the quad and then do it. Recently I was trying to look at all the settings and reading...

I have recently bought a Versacopter V2 with the GR 18 and MZ 12, I got everything setup except a bit of the radio and receiver setup. I have found out a while ago that the one of the motors would just beep over and over and wouldn't spin but the other 3 did but just today I started the...

Hi there! Greetings from Córdoba, Argentina. Its a real pleasure to join this forum. I've been playing with Flitetest free plans for over a year now and I've decided to go to my own VersaCopter. This is my very first drone. I'm having an issue when trying to level my drone. I just can't keep...

Hi there. Yet another noob looking for troubleshooting help! My Versacopter worked flawlessly for several months until I had a bad crash and rebuilt. Ever since the rebuild, it will only fly using my 3S battery. I have 2 other batteries which are 4S. When I try flying with a 4S battery, it...

I am having an issue setting up my Graupner MZ-18 for a Versacopter. Does anyone have this radio and have set it up correctly? I am new to this radio and so far the learning curve is getting to me..:black_eyed: HELP

The issue I'm having is my versacopter is drifting on liftoff. I have to Compensate on the right stick to correct it. Is there anything I can do to fix this?

Hi, I was looking into buying a versacopter v2 and using the naze32 setup. Before I invest in all of this, I was curious on programming the flight controller. Since I have a cheap transmitter, it doesn't have a screen or any of those types of functions. Just the basic controls with a few toggle...

I have been flying my Versacopter for some time now and upgraded to the new mounts. I use powerpack E and a 3 cell battery. It flies pretty well and I fly a lot in acro mode now. Sometimes I get some oscillation when I cut the throttle when lowering altitude and I cut the throttle too much. My...

So I finally completed my versacopter v2 build using Flitetest electronics pack. The only difference is I am using a dx9 and a lemonrx 8 channel ppm reciever. Used pid setting provided by the video for a baseline(I am a newb tuner). Tried to set the loop time like in the video but no matter what...

Yesterday I received some LEDs for my VersaCopter, i soldered all the connections and hot glued the LEDs in place but when i turned on my drone none of the LEDs lit up, until i enabled the LEDs, but then i can not use my 5th and 6th channels for some reason, if i disable the LEDs in clean flight...

Hey folks, I've built my Versacopter but I have a hit a bit of a snag with setting it up, here are my specs: Powerpack E Naze32 Afroflight by X8R receiver Taranis Transmitter I've double checked prop orientation, as well as calibrated the ESC's/Accelerometer at least a dozen times now. It...

Hey guys, I hope someone can answer this for me. I have very recently started getting into multirotors and fell in love right away thanks to the youtube videos from Flitetest. My first quad was a 3D printed V-tail ( http://www.thingiverse.com/make:197915 ) and I soldered the ESC pins using...

I have the power pack D for normal sized quads, would these electronics work with FliteTest's new versacopter? I know the suggestion is the racing quad pack, but would the bigger motors be to big or over powered? Is it the props they'll be swinging that's the problem? Thanks for the replies!